Abstract:In this paper, the influences of Cr3C2/VC content on WC grain size, WC grain shape and mechanical properties of WC–6 wt. % Co cemented carbides were investigated. The results showed that the grain size first rapidly decreased and then slightly decreased with the increasing Cr3C2/VC content, and VC led to finer grain size and narrower size distribution. HRTEM/EDS analysis of the WC/Co interface indicates that the segregation concentration of V is much larger than that of Cr, which may be a strong response to the higher inhibition efficiency of VC. The addition of Cr3C2 induced triangular prism shape WC grains while VC generated stepped triangular prism grains. Despite the grain growth inhibitor (GGI) mechanisms of Cr3C2/VC have been extensively studied in the literature, the doping amount, especially the doping limit, has not been systematically investigated. In this work, the saturated solubilities of Cr and V in cobalt binder phase along with carbon content hare been predicted based on thermodynamic calculations. Based on the theoretical calculations, the doping amount of Cr3C2/VC is designed to be gradually increasing until more or less over their maximum solubilities in the binder phase, thereby investigating the subsequent microstructure and mechanical properties. When the doping of Cr3C2/VC exceeds the maximum solubility in Co phase, Co-rich Cr-carbides and Co-deficient V-carbides would form respectively, which were detrimental to the transverse rupture strength (TRS) and impact toughness. The hardness increased with the increasing Cr3C2/VC content, while the fracture toughness decreased with the increasing Cr3C2/VC content. The TRS initially enhanced and then declined, but the stepped triangular prism shape grains and low fraction of WC/Co interface in WC–6Co–VC cemented carbide led to a more pronounced decline in the TRS. The sample with 0.6 wt. % Cr3C2 addition had good comprehensive mechanical properties, its hardness, fracture toughness and TRS were 1880 kg/mm2, 9.32 MPa·m1/2 and 3450 MPa, respectively.

Microstructure and Mechanical Properties of Ultra-Fine WC-10Co Cemented Carbides with Cr3C2 and NbC: Experimental Investigation Supported by Thermodynamic Calculation

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Thermodynamic Calculation Designed Compositions, Microstructure and Mechanical Property of Ultra-Fine WC-10Co-Cr3C2-TaC Cemented Carbides

The Enhancement of the Microstructure and Mechanical Performances of Ultrafine WC-Co Cemented Carbides by Optimizing Cr2(C,N) Addition and WC Particle Sizes

Effects of Cr2(C,N) Addition on Microstructure and Comprehensive Mechanical Properties of Ultrafine Cemented Carbide

Effect of (cr, V)2(C, N) on the Microstructure and Mechanical Properties of WC-10Co Cemented Carbides

Effect of the Combined Addition of TaC and NbC on the Dispersity of Cubic Phase in Ultra-Fine WC-10Co-0.5Cr Cemented Carbides

Effect of Vc and Nbc Additions on Microstructure and Properties of Ultrafine Wc-10co Cemented Carbides

Effects of Cr3C2, VC, and TaC on Microstructure, WC Morphology and Mechanical Properties of Ultrafine WC–10 wt. % Co Cemented Carbides

Structure and Performance of Ultra Fine Cemented Carbides WC-10Co-0.8 (Cr_3C_2/TaC)

Microstructures and Mechanical Properties of WC-Co-xCr-Mo Cement Carbides

Influence of NbC and VC on microstructures and mechanical properties of WC–Co functionally graded cemented carbides

Optimization of the Mechanical Properties of Ultra-Fine WC-Co-Cr3C2 Cemented Carbides Via an Approach Based on Thermodynamic Calculations and Characterization of the Experimental Results by the Weibull Distribution

Influence of Cr3C2 and VC Content on WC Grain Size, WC Shape and Mechanical Properties of WC–6.0 wt. % Co Cemented Carbides

Effects of Nano Wc and Cr3c2 on Grain Growth, Microstructure and Mechanical Properties of Ultra-Coarse Cemented Carbides

Investigation of ultrafine WC-Co-Fe-Ni-Cr<sub>3</sub>C<sub>2</sub> cemented carbide microstructure and properties based on phase diagram thermodynamics

Effect of Cr3C2 Addition on Microstructure and Mechanical Properties of WC-CoNiFe Cemented Carbides

Influence of VC/Cr3C2 and Mixed Carbon Content on Microstructure and Properties of Ultrafine WC-0.5Co Cemented Carbide

Effect of (cr0.8v0.2)2(c,n) Addition on Microstructure and Mechanical Properties of WC–8Co Cemented Carbides

The effect of NbC on mechanical properties and fracture behavior of WC–10Co cemented carbides

Sintering Behavior and Mechanical Properties of Cr3C2 Doped Ultra-Fine WC-Co Cemented Carbides: Experment Guided with Thermodynamic Calculations