Abstract:In this paper, the influences of Cr3C2/VC content on WC grain size, WC grain shape and mechanical properties of WC–6 wt. % Co cemented carbides were investigated. The results showed that the grain size first rapidly decreased and then slightly decreased with the increasing Cr3C2/VC content, and VC led to finer grain size and narrower size distribution. HRTEM/EDS analysis of the WC/Co interface indicates that the segregation concentration of V is much larger than that of Cr, which may be a strong response to the higher inhibition efficiency of VC. The addition of Cr3C2 induced triangular prism shape WC grains while VC generated stepped triangular prism grains. Despite the grain growth inhibitor (GGI) mechanisms of Cr3C2/VC have been extensively studied in the literature, the doping amount, especially the doping limit, has not been systematically investigated. In this work, the saturated solubilities of Cr and V in cobalt binder phase along with carbon content hare been predicted based on thermodynamic calculations. Based on the theoretical calculations, the doping amount of Cr3C2/VC is designed to be gradually increasing until more or less over their maximum solubilities in the binder phase, thereby investigating the subsequent microstructure and mechanical properties. When the doping of Cr3C2/VC exceeds the maximum solubility in Co phase, Co-rich Cr-carbides and Co-deficient V-carbides would form respectively, which were detrimental to the transverse rupture strength (TRS) and impact toughness. The hardness increased with the increasing Cr3C2/VC content, while the fracture toughness decreased with the increasing Cr3C2/VC content. The TRS initially enhanced and then declined, but the stepped triangular prism shape grains and low fraction of WC/Co interface in WC–6Co–VC cemented carbide led to a more pronounced decline in the TRS. The sample with 0.6 wt. % Cr3C2 addition had good comprehensive mechanical properties, its hardness, fracture toughness and TRS were 1880 kg/mm2, 9.32 MPa·m1/2 and 3450 MPa, respectively.

Thermodynamic Calculation Designed Compositions, Microstructure and Mechanical Property of Ultra-Fine WC-10Co-Cr3C2-TaC Cemented Carbides

Microstructure and Mechanical Properties of Ultra-Fine WC-10Co Cemented Carbides with Cr3C2 and NbC: Experimental Investigation Supported by Thermodynamic Calculation

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Effects of Cr3C2, VC, and TaC on Microstructure, WC Morphology and Mechanical Properties of Ultrafine WC–10 wt. % Co Cemented Carbides

Structure and Performance of Ultra Fine Cemented Carbides WC-10Co-0.8 (Cr_3C_2/TaC)

Optimization of the Mechanical Properties of Ultra-Fine WC-Co-Cr3C2 Cemented Carbides Via an Approach Based on Thermodynamic Calculations and Characterization of the Experimental Results by the Weibull Distribution

The Enhancement of the Microstructure and Mechanical Performances of Ultrafine WC-Co Cemented Carbides by Optimizing Cr2(C,N) Addition and WC Particle Sizes

Effect of the Combined Addition of TaC and NbC on the Dispersity of Cubic Phase in Ultra-Fine WC-10Co-0.5Cr Cemented Carbides

Effect of the Cubic Phase Distribution on Ultrafine WC–10Co–0.5Cr–xTa Cemented Carbide

Sintering Behavior and Mechanical Properties of Cr3C2 Doped Ultra-Fine WC-Co Cemented Carbides: Experment Guided with Thermodynamic Calculations

Effects of Cr2(C,N) Addition on Microstructure and Comprehensive Mechanical Properties of Ultrafine Cemented Carbide

Influence of Cr3C2 and VC Content on WC Grain Size, WC Shape and Mechanical Properties of WC–6.0 wt. % Co Cemented Carbides

Effects of TaC on Microstructure and Mechanical Properties of Coarse Grained WC–9Co Cemented Carbides

Investigation of WC–Co Alloy Properties Based on Thermodynamic Calculation and Weibull Distribution

High-temperature Mechanical Behavior of Ultra-Coarse Cemented Carbide with Grain Strengthening

Solubilities of Grain-Growth Inhibitors in WC-Co-based Cemented Carbides: Thermodynamic Calculations Compared to Experimental Data

Effect of (cr0.8v0.2)2(c,n) Addition on Microstructure and Mechanical Properties of WC–8Co Cemented Carbides

Influence of VC/Cr3C2 and Mixed Carbon Content on Microstructure and Properties of Ultrafine WC-0.5Co Cemented Carbide

Effect of (cr, V)2(C, N) on the Microstructure and Mechanical Properties of WC-10Co Cemented Carbides

Effect of Carbon Content on the Microstructure and Mechanical Properties of Ultrafine WC-15Co Cemented Carbides Using a Co-based Solid Solution Binder Phase

Effect of Vc and Nbc Additions on Microstructure and Properties of Ultrafine Wc-10co Cemented Carbides