Abstract:A statistical analysis of plastic deformation mechanisms was performed on an extruded Mg-3 wt%Y sheet during room temperature uniaxial compression along the extrusion direction. Grain-scale slip trace analysis and twin variant analysis were performed grain-by-grain to reveal the active slip/twinning systems based on quasi-in-situ SEM and EBSD. The initial microstructure was fully recrystallized exhibiting typical rare-earth texture characteristics. The true stress-true plastic strain curve showed a sigmoidal shape indicating a profuse twinning activity which was consistent with the twin analysis. After 10% strain, there were 78 out of ~700 grains exhibited slip trace. In addition to the dominated basal slip (79.5%), considerable non-basal slips including 2nd pyramidal slip (11.5%) following prismatic slip (9%) were active. For twinning activity, among the ~250 grains analyzed at 10% strain, all the identified ~150 twins were tension twins with an area fraction of 19%. The twin variant selection did not solely follow the Schmid law, i.e. 42.3% twins exhibited low Schmid factor values (m<0.2) and 5.4% m values was negative. However, the proposed normalized m (mnor) can correlate the variant selection more effectively, and over 80% twins exhibited large mnor values. Twin transmission at grain boundary was observed for over 50% twins, and only 43.6% of them had high Luster-Morris parameter values (m’>0.75). However, the transmitted pairs with both large mnor sum and normalized m’ were preferred, and the fraction was over 64%. The twined number fraction was closely related to the maximum m values of prismatic slip. The present work implied that the twinning behavior is greatly dependent on the local conditions, and slip and twinning are closely related.

Statistical Investigation of Deformation Mechanisms in Rolled Mg Sheet During Compression

A Statistical Analysis of Compressive Deformation Mechanisms in an Extruded Mg–3Y Sheet

Statistical Analysis Of Grain-Scale Effects Of Twinning Deformation For Magnesium Alloys Under Cyclic Strain Loading

Quantitative investigation on the {10–12} twinning-detwinning behavior and twinning transfer of an extruded Mg-2.8Y sheet during compression-tension loading via quasi-in-situ EBSD observation

Quantitative Investigation on the Slip/Twinning Activity and Cracking Behavior During Low-Cycle Fatigue of an Extruded Mg-3Y Sheet

Quasi-in Situ Electron Backscatter Diffraction Analysis of Twinning–detwinning Behavior in AZ31 Magnesium- Alloy Rolled Plates Subjected to Compression Loading in Different Directions

Twinning characteristic and variant selection in compression of a pre-side-rolled Mg alloy sheet

Analysis of the microstructure and deformation mechanisms by compression along normal direction in a rolled AZ31 magnesium alloy

Revealing slip-induced extension twinning behaviors dominated by micro deformation in a magnesium alloy

Twinning Behavior in a Rolled Mg-Al-Zn Alloy under Dynamic Impact Loading

Influence of grain size on twinning behavior of WE43 magnesium alloy during room-temperature compression deformation

Three-dimensional study of grain scale tensile twinning activity in magnesium: A combination of microstructure characterization and mechanical modeling

EBSD Analysis and Theoretical Prediction of Twin Orientations During Compression in Mg-3Al-1Zn

Three-dimensional study of grain scale tensile twinning activity in Mg: A combination of microstructure characterization and mechanical modeling

Quasi-in-situ study on {10-12} twinning-detwinning behavior of rolled Mg-Li alloy in two-step compression (RD)-compression (ND) process

Microtexture Evolution Via Deformation Twinning and Slip During Compression of Magnesium Alloy AZ31

Investigation of the Microstructural Evolution of the As-Extruded Mg–6Zn–1Mn Alloy Sheets under High Strain Rate Tensile Loading

The effects of microstructure on deformation twinning in Mg WE43

Twin recrystallization mechanisms in a high strain rate compressed Mg-Zn alloy

Local twinning behavior of ZK61m magnesium alloy sheet under multiaxial stress during drawing-pressing with Erichsen test machine

Effect of Slip on Detwinning Behavior During Multi-Direction Compression of A Wrought Magnesium Alloy