Abstract:Spray cooling, which has a fast thermal response and low flow rate consumption, is a common and effective thermal management approach for high power electronic systems. Typically, to improve the heat transfer co-efficient (HTC) for spray cooling, the target surface wettability is decreased, promoting nucleation boiling by reducing the surface energy barrier for bubble nucleation. However, the merging of bubbles and the formation of a vapor film have limitations in further increasing the critical heat flux (CHF). Hence, maximizing both the HTC and CHF of spray cooling can be mutually exclusive on the same heated surface. This paper presented a novel design for a vapor-liquid separation structure surface. It consisted of lower micropillars that serve as the vapor separation channel. On top of that, there was an upper multi-layer copper micromesh that wicks and spreads the coolant. Additionally, nano-grass attached to the micromesh to enhance capillary force and increase the nucleation sites simultaneously. Subsequently, we calculated the forward velocity and pressure drop of the droplets passing through the copper mesh to study the effects of droplet velocity and capillary force on heat transfer performance. The results show that the forward velocity of the droplets decreases rapidly as the increase of copper mesh layers and it drops to zero when passing through the third mesh. Therefore, the capillary force generated by the copper mesh is another important factor for the atomized droplets to pass through the copper mesh and reach the target surface. We have proven that all the vapor-liquid separation structure surfaces satisfy the condition Delta Pcap>Delta Ppore+Delta Plocal. Hence, the synergistic effects of the micropillar, copper micromesh, and nano-grass enable a circulation process of wicking-rewetting-vapor evacuation, which improves the onset of nucleate boiling (ONB), enhances the HTC, and increases the maximum heat flux dissipated by the system. Enhanced HTC (7.94 W/cm2/K) and maximum heat flux (817 W/cm2) were achieved at 1.50 ml/s on the vapor-liquid separation structure surfaces (#200 2-layer), representing an enhancement of 79.6% and 80.0% compared with that for the flat surface and the temperature of the heated surface at the ONB maximum decreased by approximately 30.8 degrees C.

Experimental Study on Heat Transfer Performance Using a Hybrid Cooling Method Combined of a Flat-Plate Heat Pipe and Spray Cooling

Experimental Investigation of Spray Cooling Performance in Non‐boiling Zone on Rough Superhydrophilic/hydrophobic Surfaces

Experimental Investigation on the Heat Transfer Performance and Evaporation Temperature Fluctuation of a New-Type Metal Foam Multichannel Heat Pipe

Experimental Investigation on the Temperature Distribution Characteristics of the Evaporation Section in a Pulsating Heat Pipe

Thermal management strategy for electronic chips based on combination of a flat-plate heat pipe and spray cooling

Study on Heat Transfer Performance of an Aluminum Flat Plate Heat Pipe with Fins in Vapor Chamber

Experimental Study on the Thermo-Hydrodynamic Characteristics of a Nitrogen Pulsating Heat Pipe

Investigation on Transient Behaviors of Flat Plate Heat Pipes

Thermal performance of flat plate heat pipe array with surface wettability modification: An experimental and simulation study

Liquid Plug Characteristics and Heat Transfer Performance of a Silicon-Based Ultra-Thin Flat Heat Pipe at Different Incline Angles

THE EXPERIMENTAL INVESTIGATION OF PHASE CHANGE HEAT TRANSFER IN A FLAT PLATE HEAT PIPE

Experimental Study on a Spray and Falling-Film Cooling System

Experimental investigation on a pulsating heat pipe with low number of turns at liquid hydrogen temperature range

Experimental Study on a Hydrogen Pulsating Heat Pipe in Different Heating Modes

Experimental Study on a Hydrogen Closed-Loop Pulsating Heat Pipe with Two Turns

Coupling dynamic thermal analysis and surface modification to enhance heat dissipation of R410A spray cooling for high-power electronics

Experimental and computational investigation on synergistic enhancement spray cooling using micropillars and capillary-driven wicking hybrid structures

An Experimental Investigation on the Heat Transfer Characteristics of Pulsating Heat Pipe with Adaptive Structured Channels

Experimental Study on the Thermal Performance of Flat Loop Heat Pipe Applied in Data Center Cooling

Experimental Study of Composite Heat Pipe Radiator in Thermal Management of Electronic Components

Experimental and theoretical investigation of the influence of heat transfer rate on the thermal performance of a multi-channel flat heat pipe