Abstract:Conventional straight fin (SF) radiators have difficulties meeting the cooling requirements of high-power electronic components. Therefore, based on the structure and technology of the detachable fin radiator, this paper proposes a kind of radiator embedded in the heat pipe base and uses the roll-bond flat heat pipe (RBFHP) to replace the traditional fin. The radiator has the advantages of modularity, easy manufacturing, low cost and good heat balance. In this study, the heat pipes (HPs)-RBFHPs radiator was tested in natural convection and forced convection to mimic the actual application scenario and compared with the conventional aluminum radiator. Heating power, angle, wind speed and other aspects were studied. The results showed that the cooling performance of the HPs-RBFHPs radiator was improved by 10.7% to 55% compared with that of the SF radiator under different working conditions. The minimum total thermal resistance in the horizontal state was only 0.37 °C/W. The temperature equalization of the base played a dominant role in the performance of the radiator at a large angle, and the fin group could be ineffective when the angle was greater than 60°. Under the most economical conditions with an inclination of 0° and a wind speed of 2 m/s, the input power was 340 W, the heat source temperature of the HPs-RBFHPs was only 64.2 °C, and the heat dissipation performance was 55.4% higher than that of SFs.

What problem does this paper attempt to address?

The problem this paper attempts to address is the thermal management challenge faced by high-power electronic components (such as IGBT) in integrated design. Traditional straight fin heat sinks (SF) are difficult to meet the cooling needs of these high-power electronic components, especially when the heat flux density increases, making the thermal management issue more prominent. Therefore, this paper proposes a new type of heat sink based on a detachable fin heat sink structure and technology, embedding heat pipes into the heat sink substrate and replacing traditional fins with rolled and flattened heat pipes (RBFHP). This new type of heat sink has the advantages of modularity, ease of manufacturing, low cost, and good thermal balance. Specifically, the paper experimentally studies the thermal performance of this composite heat pipe heat sink under natural convection and forced convection conditions and compares it with traditional aluminum heat sinks. The research content includes the effects of heating power, inclination angle, wind speed, and other aspects. The experimental results show that compared to traditional straight fin heat sinks, the cooling performance of this composite heat pipe heat sink is improved by 10.7% to 55% under different working conditions. Particularly in the horizontal state, the total thermal resistance is as low as 0.37 °C/W. When the inclination angle is greater than 60°, the temperature uniformity of the substrate dominates the performance of the heat sink, and the fin set may fail. Under the most economical conditions (inclination angle of 0°, wind speed of 2 m/s), when the input power is 340 W, the heat source temperature of the composite heat pipe heat sink is only 64.2 °C, and the thermal performance is 55.4% higher than that of the traditional straight fin heat sink.

Experimental Study of Composite Heat Pipe Radiator in Thermal Management of Electronic Components

Experimental Investigation on the Heat Transfer Performance and Evaporation Temperature Fluctuation of a New-Type Metal Foam Multichannel Heat Pipe

Thermal study of the natural air cooling using roll bond flat heat pipe as plate fin under multi-heat source condition

Experimental Investigation on the Temperature Distribution Characteristics of the Evaporation Section in a Pulsating Heat Pipe

Experimental Investigation on Flow and Heat Transfer Performance of a Novel Heat Fin-Plate Radiator for Electronic Cooling

Heat Transfer Performance of a 3D-Printed Aluminum Flat-Plate Oscillating Heat Pipe Finned Radiator

Experimental study on thermal and flow characteristics of metal foam heat pipe radiator

Study on LED Array Heat Radiator Improvement under Natural Convection

Experimental Study on Indirect Thermosyphon Radiator Coupled with Flat Heat Pipe for Electronic Component

Experimental Study on Heat Transfer Characteristics of Thermosyphon Radiator

Performance Evaluation and Analysis of a Vertical Heat Pipe Latent Thermal Energy Storage System with Fins-Copper Foam Combination

Study on Heat Transfer Performance of an Aluminum Flat Plate Heat Pipe with Fins in Vapor Chamber

Experimental Study on Heat Transfer Performance Using a Hybrid Cooling Method Combined of a Flat-Plate Heat Pipe and Spray Cooling

Experimental investigation on a 0.5-metre-long aluminum flat heat pipe for thermal management in electronic devices

Heat transfer characteristics of two different thermosyphon radiators for electronic device

Study of Heat Dissipation Characteristics of Loop Heat Pipe with Heat Sink of Composite Material

Numerical and Experimental Study on the Heat Dissipation Performance of a Novel System

Experimental investigation on thermal performance of ultra-thin flattened heat pipe with middle heating for electronics cooling

Performance Analysis and Structural Optimization of a Finned Liquid-Cooling Radiator for Chip Heat Dissipation

Performance analysis and optimization of heat pipe-based radiator for space nuclear power system

Experimental Study on the Thermal Performance of Flat Loop Heat Pipe Applied in Data Center Cooling