Abstract:Active materials used in lithium ion batteries consist of micro-metric ceramic particles. Mechanical failure can happen within these brittle particles due to large internal stresses provoked by lithium intercalating in the crystalline structure during charge and discharge. Their mechanical behavior is directly related to some key intrinsic parameters, namely the elastic modulus, the fracture toughness and lithium di usivity. This works deals with the development of new characterization techniques to quantify these parameters at the local scale. Obtaining quantitative measurements is notably challenging for this type of specimen due to the highly heterogeneous structure of battery electrodes. For this, spinel LiMn2O4-based commercial cathodes are proposed as material of investigation. First, composition analysis of cathode materials at di erent states of charge was done. In general it was noticed that commercial cells are not as consistent as laboratory cells: impurities are often present (Ni, Co,...) and particles can be porous agglomerates of nanoparticles as well as large single grains. However only spinel structure was detected by X-ray di raction and Rietveld analysis showed a typical lattice expansion for higher lithium concentrations. A method using nanoindentation was developed. It consists of applying a large number of indents in cathode cross-sections and subsequently ltering the measurements depending on whether they t the set of hypotheses of the Oliver and Pharr method. It was observed that for decreasing lithium concentrations, the elastic modulus and the hardness increase from 87 GPa (0% State of Charge) to 104 GPa (100% SoC) and from 7.0 GPa (0% SoC) to 8.0 Gpa (100%SoC), respectively. With the help of contact-resonance atomic force microscopy, the elastic property could also be qualitatively mapped and it seems that the particles are homogeneous. Added to micro-raman spectroscopy, it was observed that neighboring particles can have di erent lithiation levels. The fracture toughness was estimated by measuring the crack opening displacement by atomic force microscopy and applying Irwin’s near eld theory. A toughness of about 0.9 MPa·m was found but should not be taken at face-value. Irwin’s theory requires a purely elastic-brittle fracture with traction-free crack walls. Unfortunately this condition cannot be met due to the size of the particles and the toughness is surely overestimated. Associated with electron backscattered di raction, cleavage planes were also evaluated on a reference {111} wafer. It was found that cracks always propagate in the <121> direction, corresponding to {101} planes just below the surface. At higher depths (> 100 nm), the crack deviates of 30 to 40◦. The last part of this work consists of developing a model to better comprehend electrochemical strain microscopy “time spectroscopy” (ESM-TS). It is the most promising technique to quantify locally ionic di usion coe cients. An AFM cantilever is used

Elastic Modulus Identification of Particles in Particulate Composite Through Nanoindentation

Modulus Identification of Particles Embedded in Deformable Substrate Using Nanoindentation Test

Young’s Modulus of Polycrystalline Titania Microspheres Determined by in Situ Nanoindentation and Finite Element Modeling

Finite Element Analysis To The Constitutive Behavior Of Sintered Silver Nanoparticles Under Nanoindentation

Nanoindentation measurements of anisotropic mechanical properties of single crystalline NMC cathodes for Li-ion batteries

Modelling the Nanomechanical Response of a Micro Particle–matrix System for Nanoindentation Tests

Physics-guided machine learning enhanced electrostatic actuated method for in-situ measurement of Young's modulus

An improved energy method for determining Young’s modulus by instrumented indentation using a Berkovich tip

Visualization and Quantification of State of Charge-Dependent Young's Modulus of LiMn2O4 Nanosized Particles by Bimodal AFM.

Elastic constants determination of anisotropic materials by depth-sensing indentation

Measuring elastic parameters of transversely isotropic materials by cylindrical indentation

Modeling the Nanomechanical Responses of Biopolymer Composites During the Nanoindentation

Determine the unique constitutive properties of elastoplastic materials from their plastic zone evolution under nanoindentation

An Inverse Approach to Determine the Mechanical Properties of Elastoplastic Materials Using Indentation Tests

Research on Determining Elastic–Plastic Constitutive Parameters of Materials from Load Depth Curves Based on Nanoindentation Technology

Nanomechanics of Li-ion battery materials

Further Investigation of Particle Reinforced Aluminum Matrix Composites by Indentation Experiments

Mechanical Properties Study of Particles Reinforced Aluminum Matrix Composites by Micro-Indentation Experiments

Mechanical Degradation Behavior of Single Crystal LiNixMnyCozO2 Cathode in Li-Ion Battery by Indentation Analysis

Determining the Constitutive Properties of Sintered Nano Silver via Reverse Analysis and Nanoindentation

Effects of interphase, CNT waviness and temperature on the Young's modulus of CNT/metal composites