Abstract:This paper introduces a compact picosecond laser system using tapered double cladding fiber-single crystal fiber hybrid amplification technology for the first time. By modifying the Ginzburg-Landau equation, we established a simulation model and designed a passive mode-locked picosecond oscillator based on a semiconductor saturable absorber mirror. The oscillator outputs laser with a pulse width of 7.75 ps, a center wavelength of 1030.55 nm, and a spectrum width of 0.58 nm. The seed laser is stretched and amplified by the all-fiber front stage, and then injected into the tapered double cladding fiber-single crystal fiber hybrid amplifier. The laser power is amplified from 820 mw to 103.1 W, obtaining a gain of 21 dB. We used zero-phonon line pumping technology in single crystal fiber amplifier to reduce the thermal effects caused by quantum loss, thereby increasing the length of the crystal and increasing the power loading capacity. We designed a single crystal fiber amplification module using Yb:YAG with 60 mm long, 1 mm diameter and a 1 at.% doping rate for the first time. Finally a hundred-watt level picosecond laser output with a repetition frequency of 26.33 MHz, an average power of 103.1 W, a pulse width of 244.72 ps, a spectrum width of 1.16 nm, and a beam quality of M2 x = 1.368 and M2 y = 1.511 was obtained. To the best of our knowledge, this is the highest picosecond laser output power for an all-fiber front-stage combined with a single-stage single crystal fiber amplifier.

Nonlinear chirped pulse amplification for a 100-W-class GHz femtosecond all-fiber laser system at 1.5 m

Nonlinearity Optimization of Dissipative-Soliton Fiber Laser for Generation of Pulses with 350 Kw Peak Power

Vector-dispersion Compensation and Pulse Pedestal Cancellation in a Femtosecond Nonlinear Amplification Fiber Laser System.

Femtosecond Mode-locked Fiber Laser at 1 Μm Via Optical Microfiber Dispersion Management

All-Fiber High-Power 3 GHz Ultrafast Laser System At 2.0 μm

1200-W all polarization-maintaining fiber GHz-femtosecond-pulse laser with good beam quality

Sub-60-fs, Compact 1100-Nm Fiber Laser System Based on Double-Pass Pre-Chirp Managed Amplification.

High-repetition-rate All-Fiber Femtosecond Laser with an Optical Integrated Component.

3-Ghz, Ultrafast Yb-fiber Laser Sources: Closing the Spectral Gaps

High power Raman soliton generation at 1.7 μm in all-fiber polarization-maintaining erbium-doped amplifier

Microjoule Level Femtosecond Optical Pulses with Double-Cladding Fiber-Based Nonlinear Chirped-Pulse Amplification

High-Power GHz Burst-Mode All-Fiber Laser System with Sub 300 fs Pulse Duration

Femtosecond Yb-doped Tapered Fiber Pulse Amplifiers with Peak Power of over Hundred Megawatts

Self-phase modulation enabled, wavelength-tunable ultrafast fiber laser sources: an energy scalable approach.

All-Fiber Generation of Sub-30 Fs Pulses at 1.3-Μm Via Cherenkov Radiation with Entire Dispersion Management

Higher-order Mode Fiber Enables High Energy Chirped-Pulse Amplification.

High-power, 474 Fs, 31.12 MHz, All-Polarization-maintaining, 1560 Nm Fiber Laser System Based on the Chirped-Pulse Amplification

Nonlinear Propagation of the Amplified Highly Chirped Pulse and Supercontinuum Generation in Microstructured Optical Fiber

Sub-50 fs pulses generation from an all-fiber monolithic gain-managed nonlinear amplifier with CFBG-based pre-compressor

High-peak-power, single-frequency, single-mode, linearly polarized, nanosecond all-fiber laser based on self-phase modulation compensation

Compact hundred-watt level picosecond laser system based on tapered double cladding fiber-single crystal fiber hybrid amplifier