Abstract:The electrochemical co-deposition of Cr-Co oxide coatings at room temperature on 304 stainless steel (SS) was studied using an electrolyte composed of a mixture of ethylene glycol (EG), hydrated metal chloride salts (MCln∙YH2O), and water as a secondary hydrogen donor (HBD). Metallic Cu and Ni undercoats were applied to improve the adhesion of a posterior Cr-Co metallic and oxide layer. The electroactive events that took place during both electrodeposition processes were studied using cyclic voltammetry (CV) and chronoamperometry. The microstructure and composition of the surface layers were studied using scanning electron microscopy (SEM/EDS), X-ray diffraction (XRD) and cross-sectional elemental mapping via transmission electron microscopy (TEM). The surface of steel with the Cr-Co:EG-H2O coating showed greater resistance to pitting corrosion (123.93 mV) compared to untreated stainless steel (62.3 mV). This sample showed a large hystere-sis area, which is associated with high resistance to pitting corrosion by the occurrence of a re-passivation of the sample at a Erep value of 24.31 mV. After the cyclic potentiodynamic polariza-tion (CPP) test, the lowest specific mass loss (0.001 mg/cm2) was achieved for the AISI 304 SS sample coated using EG-water solvents (Cr-Co:EG-H2O), while the untreated AISI 304 SS reached a higher specific mass loss (0.01 mg/cm2). The Electrochemical Impedance Spectroscopy (EIS) tests showed that the uniform corrosion resistance varied significantly from the untreated AISI 304 SS (35 kΩ) to the coated sample (57 kΩ), which is attributed to the protection provided by the chromium and cobalt oxides coating. The best corrosion resistance achieved was correlated with a superhydrophobic character (with a contact angle of 158.41°) of the Cr-Co coatings. This was in turn a consequence of a needle-like morphology characteristic of these oxides.

Mechanism for Electrodeposition of Lead Dioxide Coating on Stainless Steel Substrate

Electrolytic Deposition of Hydroxyapatite Coating on CoNiCrMo Substrates

In-situ Zn-Al Layered Double Hydroxide Conversion Coatings Prepared on Galvanized Steels by a Two-Step Electrochemical Method

Preparation And Characterization Of Pbo2 On Aluminum Substrate

Preparation of Al-Cr-Fe Coatings by Heat Treatment of Electrodeposited Cr/Al Composite Coatings

Corrosion Resistance Mechanism of a Novel Porous Ti/Sn-Sb-RuOx/β-PbO2 Anode for Zinc Electrowinning

Preparation of WC/Co Powders by Electroless Plating and Its Coating on 2cr13 Stainless Steel by Laser Cladding

Electrodeposition of decorative and protective Zn–Fe coating onto low-carbon steel substrate

Fabrication Lead Dioxide Coating by Pulse Current Method

Analysis of the Oxidation Process of Anodic Pb(II) Films on Lead in Sulfuric Acid Solution

Study on Microstructure and Properties of Mechanically Deposited Zn-Sn Coating

Effect of the Current Density on Electrodepositing Alpha-Lead Dioxide Coating on Aluminum Substrate

Cr-Co Oxide Coatings Resistant to Corrosion, Electrodeposited on 304 SS Using an Ethylene Glycol-Water Solvent

Liquid Phase Deposited TiO2 Films on Stainless Steel Mesh for Corrosion Resistance Application

Quick fabrication of evenly porous PbO 2 through potential linear increase electrodeposition

Beta-PbO micro-octahedrons synthesized by electrochemical reduction

Microstructure and corrosion behavior of Cr and Cr–P alloy coatings electrodeposited from a Cr(III) deep eutectic solvent

Electrophoretic deposition of ZnCo2O4 spinel and its electrocatalytic properties for oxygen evolution reaction

The influence of substrate surface treatment on the electrodeposition of (Co,Mn)3O4 spinel precursor coatings

Study on Al 2 O 3 /Fe-Al gradient coating assisted prepared by ionic liquid for Lead-Bismuth eutectic corrosion resistance

Coating process conditions of W alloy electrodeposition