Abstract:Objective A group of total hip arthroplasties were followed up radiologically to in ves-tigate the relationship of the cup ab duction angle with the extent of wearing and its direction and the effects of the cup abduction angle on the stability of hip joint.Methods A series of 32hip joints(30patients)were followed up routinely.The average f ollow-up period was 4.2years.The cu p abduction angle was measured,and the sagittal displacement of fem oral head to acetabulum was also exam ined to determine the direction and degree of linear polyethylene wear.The direction and magnitude of wear were decided by measuring femoral head penetration into the polyethylene liner.A new method of computer assisted two dimensional wear mea-surement was employed in this study.The results were statistically analyzed,with a P value less than 0.05indicating significant difference.Results There were no evidences of component loosening and clinical failure among the 32hips at a latest f ollow-up.The angle between the axis femoral component and femoral shaft in all of the patients was less than 3d egrees.The average amount of linear wear was 0.81mm,and the wear rate was 0.18mm per year.The average cup abduction angle was 54.5degrees,the wear direction was?6.93degrees superior-laterally.Wear d irection had a negative correlation with cup abduction angle by linear re-gression analysis;it meaned that th e direction of wear turning from superior-medial to superior-lateral gradually along with the increasing of cup abduction angle.In the cup abduction angle of more than 55degrees,the wear direction mostly orientated superior-laterally.However,no correlation of linear wear amount with wear di rec-tion or cup abduction angle was found in linear regression analysis.Conclusion Wear direction and cup abduction angle is negatively corre lated.The wear direction points mostly superior-laterally with cup abd uction angle over 55degrees,which could re sult in uneven stress distribution a nd greater stress concentration sup e-rior-laterally,consequently increase of wear;meanwhile,if the cup is too vertical,the risk of impingemen t and dislocation increases.The study shows that acetabular components with cup abduction angle over 55de-grees should be avoided in order to ma intain hip stability and desirable r ange of motion.

THE EFFECT OF ASPHERICITY OF ACETABULAR BEARING SURFACE ON CONTACT MECHANICS OF UHMWPE TOTAL HIP IMPLANTS BY FINITE ELEMENT ANALYSIS

Analysis of Finite Element Modeling on Elasto-Plasticity of Polyethylene Liner under Contact Stress after THA

Effect of Progressive Wear on the Contact Mechanics of Hip Replacements – Does the Realistic Surface Profile Matter?

The Effect of Cup Outer Sizes on the Contact Mechanics and Cement Fixation of Cemented Total Hip Replacements

The effect of cup inclination and wear on the contact mechanics and cement fixation for ultra high molecular weight polyethylene total hip replacements.

Measurement of polyethylene wear and its clinical significance in total hip arthroplasty

The Relationship of Wearing with the Abduction Angle of the Acetabulum in Total Hip Arthroplasty

Wear Behaviour and Wear Debris Characterization of UHMWPE on Alumina Ceramic, Stainless Steel, CoCrMo and Ti6Al4V Hip Prostheses in a Hip Joint Simulator

Temperature Field and Wear Prediction for UHMWPE Acetabular Cup with Assumed Rectangular Surface Texture

Contact Mechanics and Elastohydrodynamic Lubrication in a Novel Metal-on-metal Hip Implant with an Aspherical Bearing Surface

The Effect of Cup Orientation and Coverage on Contact Mechanics and Range of Motion of Metal-On-Metal Hip Resurfacing Arthroplasty

Three-dimensional Finite Element Analysis of Acetabular Prosthesis in an Adult Patient with Total Hip Arthroplasty for High Dislocation

Numerical wear study of metal‐on‐ultrahigh molecular weight polyethylene‐based cervical total disc arthroplasty by coupling finite element analysis and multi‐body dynamics

Evaluation of Surface Finish and Dimensional Control of Tribological Metal-Ultra High Molecular Weight Polyethylene Pair of Commercially Available Hip Implants

Contact Mechanics Studies of an Ellipsoidal Contact Bearing Surface of Metal-on-metal Hip Prostheses under Micro-Lateralization.

[Three-dimensional finite element analysis of acetabular prosthesis in an adult patient with total flip arthroplasty for high dislocation].

Nonsphericity of Bearing Geometry and Lubrication in Hip Joint Implants

Influence of Cross-Shear and Contact Pressure on Wear Mechanisms of PEEK and CFR-PEEK in Total Hip Joint Replacements

Contact Mechanics of Non-Spherical Hip Joint Replacements

The influence of PEEK acetabular shell on the mechanical stability of total hip replacements under gait loading and motion

Biotribological Behavior of Ultra High Molecular Weight Polyethylene Composites Containing Coralline Hydroxyapatite in a Hip Joint Simulator