Abstract:Introduction: Besides head-insert articulation in hip joint replacements, micro-motions between the backside of assembled polyethylene acetabular liners and the metal cup may cause additional wear. Pelvic osteolysis frequently occurs in the region of screw holes, and cup loosening hints to clinically relevant amounts of polyethylene backside wear. It has yet to be confirmed whether backside wear particles differ in size and morphology compared to articulating wear. Previous methods have been limited to subjective assessment of backside surface damages without consideration of wear debris. The aim of this study was to develop and validate a method for quantitative in vitro measurements of polyethylene backside wear in artificial hip cups and to characterize these wear particles for the first time. Methods: Titanium cup-systems (Plasmafit®Plus7, Aesculap, UHMWPE liner) were sinusoidally loaded (2.5 kN) and a torque of 5 Nm was simultaneously applied. The front and rear side of the cup were separated to isolate backside wear. After 2 × 106 cycles the surrounding fluid was filtered and a particle analysis was performed. Results: Backside wear had a particles size of 64.1 ± 1.9 nm and was verified as round and oval particles with partly rough outlines. An estimated total number of particles of 1.26 × 109 ± 1.67 × 108 per 106 cycles was determined. Conclusion: Backside wear was estimated to be several times lower than published values of articulating wear. However, polyethylene backside wear particles represented significantly smaller particles with partly roughened outlines than articulating wear particles and may therefore cause higher biological response in macrophage-mediated bone resorption compared to articulated particles. Statement of significance: Within this study, an analytical method for quantitative measuring polyethylene backside wear of artificial hip cups was successfully developed and validated for the first time. It could be shown that backside wear is still present, even in modern cup-systems. These findings can be further used for investigations of the osteolytic potential of polyethylene particles, for evaluating and improving new implant systems and to evaluate the effectiveness of screw hole plugs to prevent the particle migration to the acetabulum.

Wear behaviour of cross-linked polyethylene assessed in vitro under severe conditions

Comparative wear and wear debris under three different counterface conditions of crosslinked and non-crosslinked ultra high molecular weight polyethylene

Wear Behaviour and Wear Debris Characterization of UHMWPE on Alumina Ceramic, Stainless Steel, CoCrMo and Ti6Al4V Hip Prostheses in a Hip Joint Simulator

Scanning Electron Microscopy and Energy-Dispersive X-Ray Spectroscopy as a Valuable Tool to Investigate the Ultra-High-Molecular-Weight Polyethylene Wear Mechanisms and Debris in Hip Implants

Measurement of polyethylene wear and its clinical significance in total hip arthroplasty

[In-Vitro Analysis of Polyethylene Liner Wear Performance at 3 and 5 Million Cycles]

Structural profile of ultra-high molecular weight polyethylene in acetabular cups worn on hip simulators characterized by confocal Raman spectroscopy.

Study on Biocompatibility, Tribological Property and Wear Debris Characterization of Ultra-Low-wear Polyethylene As Artificial Joint Materials.

Do temperature variations at the bearing surface during gait affect polyethylene wear in Charnley low-friction arthroplasty of the hip? Simulator study comparing UHMWPE and highly cross-linked polyethylene

Development of an extremely wear-resistant ultra high molecular weight polyethylene for total hip replacements

Mechanisms of plastic deformation in highly cross-linked UHMWPE for total hip components--the molecular physics viewpoint.

Biotribology Behavior of Ultra-High Molecular Weight Polyethylene Against Carbon/Carbon Composites Used for Hip Joint Replacement

Surface Modifications Induced by In-Vitro Wear and Oxidation on Γ-Irradiated UHMWPE Hip Liners Belonging to Different Commercial Generations

Backside wear in acetabular hip joint replacement

Non-destructively Differentiating the Roles of Creep, Wear and Oxidation in Long-Term in Vivo Exposed Polyethylene Cups

Total Hip Wear Assessment: A Comparison Between Computational and In Vitro Wear Assessment Techniques Using ISO 14242 Loading and Kinematics

Wear Simulation of Ceramic-on-Crosslinked Polyethylene Hip Prostheses: A New Non-Oxide Silicon Nitride versus the Gold Standard Composite Oxide Ceramic Femoral Heads.

Structural modifications induced by compressive plastic deformation in single-step and sequentially irradiated UHMWPE for hip joint components

Wear Mechanism and Wear Debris Characterization of ULWPE in Multidirectional Motion

Long-term Radiographic Assessment of Cemented Polyethylene Acetabular Cups

Wear and deformation of ceramic-on-polyethylene total hip replacements with joint laxity and swing phase microseparation