Abstract:Introduction: Besides head-insert articulation in hip joint replacements, micro-motions between the backside of assembled polyethylene acetabular liners and the metal cup may cause additional wear. Pelvic osteolysis frequently occurs in the region of screw holes, and cup loosening hints to clinically relevant amounts of polyethylene backside wear. It has yet to be confirmed whether backside wear particles differ in size and morphology compared to articulating wear. Previous methods have been limited to subjective assessment of backside surface damages without consideration of wear debris. The aim of this study was to develop and validate a method for quantitative in vitro measurements of polyethylene backside wear in artificial hip cups and to characterize these wear particles for the first time. Methods: Titanium cup-systems (Plasmafit®Plus7, Aesculap, UHMWPE liner) were sinusoidally loaded (2.5 kN) and a torque of 5 Nm was simultaneously applied. The front and rear side of the cup were separated to isolate backside wear. After 2 × 106 cycles the surrounding fluid was filtered and a particle analysis was performed. Results: Backside wear had a particles size of 64.1 ± 1.9 nm and was verified as round and oval particles with partly rough outlines. An estimated total number of particles of 1.26 × 109 ± 1.67 × 108 per 106 cycles was determined. Conclusion: Backside wear was estimated to be several times lower than published values of articulating wear. However, polyethylene backside wear particles represented significantly smaller particles with partly roughened outlines than articulating wear particles and may therefore cause higher biological response in macrophage-mediated bone resorption compared to articulated particles. Statement of significance: Within this study, an analytical method for quantitative measuring polyethylene backside wear of artificial hip cups was successfully developed and validated for the first time. It could be shown that backside wear is still present, even in modern cup-systems. These findings can be further used for investigations of the osteolytic potential of polyethylene particles, for evaluating and improving new implant systems and to evaluate the effectiveness of screw hole plugs to prevent the particle migration to the acetabulum.

Active Feedback Control of the Wall Stabilized External Kink Mode *

Wear behaviour of cross-linked polyethylene assessed in vitro under severe conditions

Measurement of polyethylene wear and its clinical significance in total hip arthroplasty

Effect of deferasirox + erythropoietin vs erythropoietin on erythroid response in Low/Int‐1‐risk MDS patients: Results of the phase II KALLISTO trial

Formulation and selection of composite biomaterials for acetabular cup of hip prosthesis with wear analysis

Isolation and characterization of UHMWPE wear particles down to ten nanometers in size from in vitro hip and knee joint simulators

Triplex-forming oligonucleotides with unexpected affinity for a nontargeted GA repeat sequence.

Tribo-biological deposits on the articulating surfaces of metal-on-polyethylene total hip implants retrieved from patients

Total Hip Wear Assessment: A Comparison Between Computational and In Vitro Wear Assessment Techniques Using ISO 14242 Loading and Kinematics

The minimum retinal irradiance required for viewing human fundi in indirect ophthalmoscopy.

[In-Vitro Analysis of Polyethylene Liner Wear Performance at 3 and 5 Million Cycles]

Comparative wear and wear debris under three different counterface conditions of crosslinked and non-crosslinked ultra high molecular weight polyethylene

Long-term Radiographic Assessment of Cemented Polyethylene Acetabular Cups

Is mild gastric epithelial dysplasia an indication for follow-up?

Backside wear in acetabular hip joint replacement

Fretting Corrosion, Third-Body Polyethylene Damage, and Cup Positioning in Primary vs Revision Dual Mobility Total Hip Arthroplasty

Polyethylene wear and osteolysis in H/G cementless total hip arthroplasty]

Impact of UHMWPE texture on friction and wear resistance of hip prosthesis

Prior invasive fungal infection is not a contraindication for subsequent allogeneic bone marrow transplantation in adult patients with hematologic malignancies.

In Vitro Analysis of Wearing of Hip Joint Prostheses Composed of Different Contact Materials

Effects of muscle potential depression and muscle stimulation caused by different insulation coating configurations on cardiac pacemakers