Abstract:One of challenges in improving the performance and cost‐effectiveness of SOFCs (solid oxide fuel cells) is the development of suitable interconnects materials. Chromia‐forming alloys and especially ferritic stainless steels, like Crofer22APU, are considered to be among the most promising candidate materials as interconnects in SOFC stacks. However, the performance of chromia‐forming materials can be limited by the low electronic conductivity of the oxide scale (high ASR – area specific resistance – value). Such degradation are unacceptable regarding the long‐term operation (>40 000 h). A previous study 1 demonstrated that in air, the addition of a nanometric reactive element oxide (La2O3) layer applied by metal organic chemical vapor deposition (MOCVD) drastically improved both corrosion rate and electrical properties of Crofer22APU and Haynes230 alloys for 100 h at 800 °C. In this present study coating performances were checked after 10 months (7500 h) and 20 months (15 000 h) at 800 °C in air. The corrosion products were carefully analyzed by SEM, EDX, and XRD. ASR measurements are realized after long time exposure. This study demonstrates that the Crofer22APU alloy has a good oxidation resistance after 15 000 h in air but this alloy has an ASR value equal to 0.370 Ω cm2. The coatings composed of a thin reactive element oxide such as La2O3 resulted in an important improvement in the high temperature oxidation resistance; the ASR values are equal to 0.154 Ω cm2. Haynes230 alloy has a better oxidation resistance but the formation of an insulating Al2O3/SiO2 layer could be detrimental.

Ni–Mo–Cr Alloy for Interconnect Applications in Intermediate Temperature Solid Oxide Fuel Cells

Performance Evaluation of a New Fe-Cr-Mn Alloy in the Reducing Atmosphere of Solid Oxide Fuel Cells

Properties of Fe–Cr Based Alloys As Interconnects in a Solid Oxide Fuel Cell

Oxidation Behavior and Electrical Property of A Ni-Based Alloy in Sofc Anode Environment

Cr-Based Alloy Used as Interconnect in Solid Oxide Fuel Cells

Application of Fe–Cr Alloys to Solid Oxide Fuel Cells for Cost-Reduction

Metallic Interconnect Materials Used in Solid Oxide Fuel Cell

A novel low Cr-containing Fe–Cr–Co alloy for metallic interconnects in planar intermediate temperature solid oxide fuel cells

Characterization of a New Fe-based Alloy As Metallic Interconnect in SOFC Anode Environment

Chemical compatibility and electrical contact between Ni–Cr–Mo alloy and LaCo0.6Ni0.4O3−δ in intermediate temperature solid oxide fuel cells

Interaction Between (la, Sr)MnO3 Cathode and Ni–Mo–Cr Metallic Interconnect with Suppressed Chromium Vaporization for Solid Oxide Fuel Cells

Metallic Interconnects for Solid Oxide Fuel Cell: Performance of Reactive Element Oxide Coating During 10, 20 and 30 Months Exposure

Porous Ni–Fe Alloys As Anode Support for Intermediate Temperature Solid Oxide Fuel Cells: I. Fabrication, Redox and Thermal Behaviors

Development of Coating Materials on Alloy Interconnect in Solid Oxide Fuel Cell

Metallic Co with Reactive Element Oxide Composite Coatings for Solid Oxide Fuel Cell Interconnect Applications

NiMn2O4 Spinel As an Alternative Coating Material for Metallic Interconnects of Intermediate Temperature Solid Oxide Fuel Cells

Characterization of Fe–Cr Alloys for Reduced Operation Temperature SOFCs

Research on Fabrication and Property of NiMn2 O4 Coatings for Fe-Cr Alloy Interconnect Applications

High-entropy FeCoNiMnCu alloy coating on ferritic stainless steel for solid oxide fuel cell interconnects

Metallic interconnects for solid oxide fuel cell: Performance of reactive element oxide coating during long time exposure

Evaluation of Fe-Cr Alloys As Interconnects for Reduced Operation Temperature Sofcs