Abstract:Bulk metallic glass(BMG) Cu58Zr20Ti20Mo2 rods with a diameter of 3 mm were prepared by using copper mould suction cast.The structure,thermal stability,compression strength and fracture morphology of this bulk metallic glass were investigated by X-ray diffractometry,differential scanning calorimetry,compression tester and scanning electronic microscopy.The results indicate that a small addition of molybdenum is beneficial for improving glass-forming ability in Cu60Zr20Ti20 system.This amorphous alloy shows a two-stage crystallization,the glass-transition temperature is about 422.6 ℃ and the onset of crystallization temperature is 453.4 ℃.Moreover,this amorphous alloy exhibits a linear relation between the stress and strain and shows a brittle fracture mode.The compression strength is about 1 720 MPa and the elongation about 3.4%.The surface morphology of fracture shows a clear vein pattern.The characteristics of both compression behaviour and fracture of Cu57Zr20Ti20Mo3 alloy with a small amount of amorphous phase are similar to those of the above fully amorphous alloy,but the strength decreases to 1 546 MPa,the elongation is 3.4% and the vein pattern becomes a little disordered and some liquid drops can be observed in the fracture surface.

Extrusion Properties of Bulk Amorphous Alloy Zr_(55)Al_(10)Ni_5Cu_(30)

Introducing Equiaxed Grains and Texture into Ni-Mn-Ga Alloys by Hot Extrusion for Superplasticity

On the atomic structure of Zr–Ni and Zr–Ni–Al metallic glasses

Bulk Nanostructure Formation Directly From The Multicomponent Alloy Melt

Study on isothermal crystallization kinetics of Zr55.7Cu22.4Ni7.2Al14.7 bulk amorphous alloy

Unusual Solidification Behavior of a Zr–Cu–Ni–Al Bulk Glassy Alloy Made from Low-Purity Zr

Formation, Thermal Stability and Mechanical Properties of Zr-Nb-Cu-Ni-Al Bulk Metallic Glasses

Formation and mechanical properties of bulk Cu-Ti-Zr-Ni metallic glasses with high glass forming ability

Structure of the amorphous, massive-metallic-glass forming Ni 25 Zr 60 Al 15 alloy from molecular dynamics simulations

Structure and properties of Zr–Ta–Cu–Ni–Al bulk metallic glasses and metallic glass matrix composites

Formation and mechanical properties of Cu_(58)Zr_(20)Ti_(20)Mo_2 bulk metallic glass

Numerical simulation and experimental verification of large-sized Zr-based bulk metallic glass ring-shaped parts in casting process

Structural Properties and Thermal Stability of Glassy (Zr<sub>.65</sub>Al<sub>.075</sub>Cu<sub>.175</sub>Ni<sub>.1</sub>)<sub>100-x</sub>Fe<sub>x</sub> (x≤20) Alloys Prepared by Mechanical Alloying

Deformation behavior of Zr-based bulk nanocrystalline amorphous alloys

Influence of Size-Dependent Free Volume Variation and Distribution on the Thermoplastic Flow Behavior of Zr-based Bulk Metallic Glass

Zr–(Cu,Ag)–Al Bulk Metallic Glasses

Homogeneity of the Superplastic Zr64.13Cu15.75Ni10.12Al10 Bulk Metallic Glass

Isothermal Stability and Selected Mechanical Properties of Zr48Cu36Al8Ag8 Bulk Metallic Glass

On Mechanical Properties and Superplasticity of Mg–15Al–1Zn Alloys Processed by Reciprocating Extrusion

Research Progress of High Strength Zr-based Bulk Amorphous Alloys

Mechanical Properties of a Cu 55 Zr 30 Ti 10 Pd 5 Bulk Amorphous Alloy