Abstract:For an accelerator magnet, a certain mechanical strength is required to sustain against a transverse compression stress due to Lorentz force. A bronze-route Nb3Sn wire with Cu-Nb reinforcement was developed by Tohoku University and Furukawa Electric to enhance the strength against axial tension. The Cu-Nb reinforcement wire also exhibited some indication of strength improvement against transverse compression; however, the details of a reinforcement mechanism for the transverse compression stress have not been clarified. In this study, the internal strains of Nb3Sn bronze-route wires with and without the Cu-Nb reinforcement under transverse compression stress were evaluated by neutron diffraction at BL19 (TAKUMI) in J-PARC. The samples were attached to jig with solder only at the ends and compression was applied at the center of the samples with 30-mm anvil with 5-mm wide and 8- to 15-mm high beam. Since a critical current, Ic of a superconducting wire depends on the three-dimensional strain, internal strain of Nb3Sn along the axial and two orthogonal radial directions were evaluated at room temperature (RT). In the different setup, Ic measurements of the wires under transverse compression stresses were also performed at 4.2 K and 14.5 T. Using 3-mm wide anvil, the transverse compression was applied at 4.2 K or RT. The neutron diffraction results indicated no significant differences in the internal strains of Nb3Sn under transverse compression between the samples with and without Cu-Nb reinforcement, while the Ic measurements showed potential increase in the irreversible stress (irr) for Cu-Nb reinforced wires. The reason for this discrepancy was discussed based on the difference in the experimental setups for each measurement.

Study of Fault Conditions During Heat Treatment of Nb3Sn Strand

Influence of heat treatment excursion on critical current and residual resistivity ratio of ITER Nb3Sn strands

Residual Stress in Nb3Sn Superconductor Strand Introduced by Structure and Stoichiometric Distribution after Heat Treatment

Study on internal strain distribution of the high-field Nb3Sn superconducting accelerator magnets with homogenization theory

Thermomechanical Behavior of the HL-LHC 11 Tesla Nb3Sn Magnet Coil Constituents during Reaction Heat Treatment

Research on Insulation Technology for Nb3Sn Layer Coil of Superconducting Conductor Testing Facility

Preparation of Nb 3 Al Superconductor by Powder Metallurgy and Effect of Mechanical Alloying on the Phase Formation

Study on the High Temperature Heat Treatment Process Optimization of Different Sizes High Jc Nb 3 Sn Wire Produced by WST

Impact of local plastic deformation on thermo-magnetic instability of high-J c Nb 3 Sn strand

An Effective Thermal Conductivity and Thermomechanical Homogenization Scheme for a Multiscale Nb3Sn Filaments

Atomic behavior of nickel-based single crystal superalloy during heat treatment process based on molecular dynamics

Effect of grain boundary deformation on the critical temperature degradation of superconducting Nb3Sn under hydrostatic pressure

Comparative Study on the Strain-Dependent Mechanical and Electronic Properties of Nb3Al and Nb3Sn

The stability of the high temperature superconducting DC coils with defects

Internally Oxidized Nb3Sn Strands with Fine Grain Size and High Critical Current Density

Experimental verification of the temperature and strain dependence of the critical properties in Nb/sub 3/Sn wires

Analysis of mechanical behavior in inhomogeneous high-temperature superconductors under pulsed field magnetization

Holistic numerical simulation of a quenching process on a real-size multifilamentary superconducting coil

Electromagnetic, stress and thermal analysis of the Superconducting Magnet

Study of air heat treatment on Bi-2223/Ag superconducting tapes

Internal Strain Measurement by Neutron Diffraction Under Transverse Compressive Stress for Nb 3 Sn Wires With and Without Cu-Nb Reinforcement