Abstract:Ti2AlNb-based alloys are developed from conventional titanium aluminides (TiAl-based alloys and Ti3Al-based alloys). Comparing with TiAl and Ti3Al-based alloys, Ti2AlNb-based alloys have better mechanical properties of strength density ratio, high temperature fracture toughness and creep resistance. It is expected to replace traditional high temperature materials such as nickel-based alloys for the manufacture of aero-engine components. Laser shock peening (LSP) is an advanced surface modification technology which induces high amplitude, large depth residual compressive stress on the surface of materials. It can effectively enhance mechanical properties of material such as micro-hardness, fatigue resistance, high temperature oxidation performance. Compared to other surface modification technologies such as shot peening and rolling, LSP can not only induce deeper compress residual stress (1-2 mm), which is about five to ten times dwms than that of shot peening, but it can refine the grain or even form nanocrystals which plays a significant role in enhancing properties of material. For these reasons, this surface treatment technology has been widely used in the aircraft and nuclear energy industries. In this paper, the surface modification of Ti2AlNb alloy was carried out by laser shock peening, and the microstructure evolution, residual stress and the performance at high temperature were investigated. The results show that laser shock peening can significantly reduce the grain size of the surface of Ti2AlNb alloy. Dislocation lines, dislocation tangles and dislocation walls were generated after LSP. The micro-hardness is increased from 350 ITV to 395 HV and the effect layer is about 1.2 mm. The residual compressive stress of -337 MPa is generated on the surface of the sample. In addition, residual stress is released obviously at high temperature. The residual stress on the surface of sample reduces to -65 MPa after heat treatment at 720 degrees C for 4 h. The residual stress is almost completely released after heat treatment at 720 degrees C for 10 h. However, the release rate of residual stress is slowed down at 600 degrees C. The effect of laser shock peening is still presence after heat treatment for 100 h.

An Investigation on the Effect of Change in Experimental Sequence of Warm Laser Shock Peening and Laser Shock Peening on the Performance of DD6 Nickel-Based Single-Crystal Superalloy

The Effect of Warm Laser Shock Peening on the Thermal Stability of Compressive Residual Stress and the Hot Corrosion Resistance of Ni-based Single-Crystal Superalloy

An Investigation of the Effect of Warm Laser Shock Peening on the Surface Modifications of [001]-Oriented DD6 Superalloy

Effect of Warm Laser Shock Peening on the Low-Cycle Fatigue Behavior of DD6 Nickel-Based Single-Crystal Superalloy

Impact on Mechanical Properties and Microstructural Response of Nickel-Based Superalloy GH4169 Subjected to Warm Laser Shock Peening

Mechanism of High Temperature Mechanical Properties Enhancement of Ni-based Superalloys Repaired by Laser Directed Energy Deposition: Microstructure Analysis and Crystal Plasticity Simulation

Effects of Residual Stress Induced by Laser Shock Peening on Mixed-Mode Crack Propagation Behavior in 7075-T6 Aluminum Alloy Panel

Effect of Ultrasonic-Assisted Surface Plastic Deformation on the Microstructures and Tensile Properties of Discrete Laser Hardening Treated Cr–Ni–Mo Alloyed Steel

Surface strengthening and fatigue life improvement of single crystal Ni-based superalloys via laser shock peening without coating

Thermal Evolutions of Residual Stress and Strain Hardening of GH4169 Ni-based Superalloy Treated by Laser Shock Peening

Characteristics of microstructure evolution of surface treated IN718 superalloy by warm laser shock peening during long-term aging at high temperatures

Laser Shock Peening of GH4133 Nickel-based Superalloy

Optimization of multiple laser shock peening on high-cycle fatigue performance of aluminized AISI 321 stainless steel

Feasibility Study of Microscale Laser Shock Processing Without Absorbing Coating to Improve High-Cycle Fatigue Performance of DZ17G Directionally Solidified Superalloy

Comparison of surface integrity of GH4169 superalloy after high-energy, low-energy, and femtosecond laser shock peening

Microstructural evolution and mechanical behaviors of Al-Cu-Li alloy processed by laser shock peening

Effects of laser shock processing on fatigue property of GH742 Ni-based superalloy

Research on Finite Element Simulation and Recrystallization of Laser Shock Peened Nickel-Based Single-Crystal Superalloy

Effect of Laser Shock Peening on Microstructure and Residual Stress of Ti2AlNb Alloy

Experimental and numerical investigation on residual stress of 316L SS treated by different laser shock peening parameters

The effect of laser shock processing on the microstructures and properties of 2060 Al Li alloys