Abstract:In this work, the most efficient and common engineered surface treatments identified as shot peening (SP), laser shock peening (LSP) and ultrasonic surface rolling process (USRP) were utilized to impact the 300 M ultrahigh strength steel. The microstructure evolution and surface strengthening behavior were carefully characterized and compared for the 300 M steel with various treatments. Besides, the underlying mechanisms for difference in grain refinement and surface mechanical properties by the arranged surface modification are revealed. The results indicate that a gradient structure with nano-grains at the top surface appears on the SP, LSP and USRP treated samples. The process of repeated impacts of SP in different directions leads to activation of multiple slip systems, which thus causes severe refined grains and dense dislocation activities associated with dislocation tangles, dislocation walls and blocking. A great variety of strikes per unit area by USRP results in higher plastic deformation compared to SP where numerous dislocation cells and deformation bands were generated. In contrast to SP and USRP, fewer slip systems are activated in LSP due to the short duration time which thus leads to the thinnest refined grain layer and more planar dislocation structures. The combination of low plastic work and lack of refined grains leads to lowest full width at half maximum (FWHM) in case of LSP samples whereas high FWHM comes from both fine grain size and dislocations in SP. The grain refinement and plastic work contributes to an increase of microhardness and compressive residual stress for the SP, LSP and USRP samples. To be clear, SP leads to a higher magnitude of hardness and compressive residual stress on the topmost surface while LSP causes a larger depth due to that shock wave in LSP influences material to much greater depth. Besides, the decomposition and redistribution of carbides are also noticed on the surface layer after the surface treatments with very high strain rate where numerous dislocations accumulate at the border of the carbides and slip trace is also observed within the carbides.

Effect of Ultrasonic-Assisted Surface Plastic Deformation on the Microstructures and Tensile Properties of Discrete Laser Hardening Treated Cr–Ni–Mo Alloyed Steel

Effect of distribution status of the spot matrix on tensile behavior for 42CrMoV when conducting discrete laser surface strengthening: Based on experiment and simulation

Mechanism of High Temperature Mechanical Properties Enhancement of Ni-based Superalloys Repaired by Laser Directed Energy Deposition: Microstructure Analysis and Crystal Plasticity Simulation

Rolling contact fatigue behaviors of 25CrNi2MoV steel combined treated by discrete laser surface hardening and ultrasonic surface rolling

The Effects of Laser‐Assisted Ultrasonic Nanocrystal Surface Modification on the Microstructure and Mechanical Properties of 300M Steel

An Investigation on the Effect of Change in Experimental Sequence of Warm Laser Shock Peening and Laser Shock Peening on the Performance of DD6 Nickel-Based Single-Crystal Superalloy

Effects of Process Parameters on Microstructure and Wear Properties of 40CrNiMo Steel by Laser Transformation Hardening

Effects of ultrasonic shot peening process on the microstructure and mechanical properties of nickel-based superalloys formed by selective laser melting

Effect of heat treatment on microstructure and mechanical properties of Fe–Cr–Ni–Co–Mo maraging stainless steel produced by selective laser melting

Microstructure evolution and surface strengthening behavior of 300 M ultrahigh strength steel under engineered surface treatments

Effect of Laser Quenching-Shock Peening Strengthening on the Microstructure and Mechanical Properties of Cr12MoV Steel

Effect of High-Temperature Heat Treatment on Strengthening Mechanism of AlCoCrFeNi Component Fabricated by LMD

Effect of Heating-Assisted Ultrasonic Surface Rolling on the Microstructure Evolution and Wear Behavior of Martensitic Steel

Study on laser surface hardening process of 30CrMnSiNi2A ultra-high strength steel fabricated by laser deposition manufacturing

Effects of Heat Treatment on the Microstructure and Properties of a Face-Centered Cubic CoCrMoW Alloy Prepared Via Laser Powder Bed Fusion

Thermomechanical response and strengthening effect of femtosecond laser-irradiated CoCrFeNi high-entropy alloy films

Carbide-facilitated nanocrystallization of martensitic laths and carbide deformation in AISI 420 stainless steel during laser shock peening

Strengthening CrFeCoNiMn0.75Cu0.25 high entropy alloy via laser shock peening

Effect of laser direct metal deposition process on the microstructure and mechanical properties and temperature and stress fields of 24CrNiMo

Study on the Surface Integrity Distribution of 300M Ultrahigh Strength Steel Subjected to Different Surface Modification Treatments

Exploring the Strengthening Mechanisms of Additive Manufactured Metals Treated by Ultrasonic Nanocrystal Surface Modification