Abstract:It is well known that the multi-axis machining technology has been developed into a key technique applied in the manufacturing field. The machined surface integrity is one of the most important factors influencing the performance of the produced components. Hence, this research concentrated on the machined surface integrity induced by the multi-axis milling operation with different inclination angle combinations. In this research work, the cutting conditions of the conventional or up-milling process with tool orientations were divided into eight different types, and the machining characteristics corresponding to different cutting strategies were discussed. The varying conditions of surface topography, texture and other machining features induced in machining process which corresponds to different inclination angle combinations were analyzed by geometrical analysis, and the surface roughness and linear profile along specific directions on the machined surface were also investigated. There is a special corresponding relationship between the rotation angle and tool tilt and lead angles. Better surface roughness could be achieved when rotation angles are 0° (positive lead), 60° (combination of positive tilt and positive lead), 90° (positive tilt) and 330° (combination of negative tilt and positive lead). Then, the samples used for study of the metamorphic layer were produced by lapping and polishing process, and the macro hardness (HL) and micro-hardness (HV) of the top machined surface were investigated. According to the measured results of both Leeb hardness and micro-hardness, higher surface hardness could be obtained under rotation angles of 60° (combination of positive tilt and positive lead), 120° (combination of positive tilt and negative lead) and 210° (negative tilt and negative lead). Moreover, the variations of the micro-hardness along the depth direction of the samples were studied. Finally, discussions on the machined surface residual stresses in both feed and cross-feed direction were carried out. Compressive surface residual stress in both feed and cross-feed direction could be generated when rotation angles are 210° (combination of negative tilt angle with smaller value and negative lead angle with larger value) and 330° (combination of negative tilt angle with smaller value and positive lead angle with larger value). Generally, the evaluation indicators of surface integrity are not all very satisfying under one special cutting condition with a certain inclination angle combination, and the optimal cutting parameters should be selected based on the specific application requirements. Finally, the optimal tool orientations and related cutting parameters were recommended, and further studies of the related topics were also presented.

Part Functionality Alterations Induced by Changes of Surface Integrity in Metal Milling Process: A Review

Influence of Thermal Mechanical Coupling on Surface Integrity in Disc Milling Grooving of Titanium Alloy

Enhancing the Machining Performance by Cutting Tool Surface Modifications: a Focused Review

Research on surface integrity and its influencing factors in the high-speed cutting of typical aluminum/titanium/nickel alloys: a review

Evolution of Hole Surface Integrity in Successive Processing Using Sequential Milling and Laser Shock Peening

Effect of Machining on Performance Enhancement of Superficial Layer of High-Strength Alloy Steel

Research status of influence mechanism of surface integrity on fatigue behavior of metal workpieces: a review

Effect of Machined Surface Integrity on Fatigue Performance of Metal Workpiece: A Review

Research Progress of the Microstructure on Machined Surface of Titanium Alloys

Surface Integrity And Fatigue Strength Of Hard Milled Surfaces

A review on theories/methods to obtain surface topography and analysis of corresponding affecting factors in the milling process

Study on Surface Integrity in Hard Milling of Hardened Die Steel

Research on the Machined Surface Integrity under Combination of Various Inclination Angles in Multi-Axis Ball End Milling

3D surface topography analysis and functionality-related performance of the machined surface in slot micro-milling titanium alloy Ti6Al4V

The Surface Integrity in Machining Hardened Steel Skd11 for Die and Mold

Research on Surface Integrity in Milling Inconel718 Superalloy

Surface Integrity and Wear Evolution of High Strength Aluminum Alloy after High-Speed Oblique Cutting

Cutting condition effects on microstructure and mechanical characteristics of Ni-based superalloys—a review

Control Rules of Surface Integrity and Formation of Metamorphic Layer in High-Speed Milling of 7055 Aluminum Alloy

Intelligent Monitoring of Surface Integrity and Cutter Degradation in High-speed Milling Processes

Framework of Surface Integrity Model for Machined Components