Abstract:Microstructural modification for the molten pool can improve mechanical properties of the selective laser melting 316 L stainless steel (SLM 316 L SS) at high-velocity deformation and can promote application of the SLM 316 L SS in the field of high-velocity deformation. Mechanical properties of the SLM 316 L SS with different volumetric energy densities (VED) were obtained at high-velocity deformation by using a split Hopkinson pressure bar (SHPB). With strain rate increased, compressive strength of the SLM 316 L SS peaked at the strain rates of 1200 s−1 - 1450 s−1. Analyzed molten pool and mechanical properties of SLM 316 L SS at the strain rate of 1200 s−1 - 1450 s−1, the SLM 316 L SS with volumetric energy density of 145.83 J/mm3 had a combination of minimum overlap ratio of molten pool and maximum single pass molten pool width, which brought maximum pool size and exhibited excellent impact energy and compressive strengths, reaching 1185 MPa and 125.4 MJ/m3, respectively. Scanning electron microscope (SEM) and transmission electron microscope (TEM) were used to characterize molten pools of the SLM 316 L SS. Microcracks appear along molten pool boundaries of the failed specimens was found and poor deformation coordination ability due to the misorientation of grains on both sides of molten pool boundaries makes the molten pool boundary as the weak region. Overlap ratio of the molten pool and theoretical width of the single pass molten pool are considered to be main factors in determining the molten pool size, which in turn determines mechanical properties of the SLM 316 L SS at high-velocity deformation. Further, in the process of dynamic compression deformation, microcracks were formed at the molten pool boundary, which lead to failure of the SLM 316 L SS.

Effect of scanning speed and laser power on formability, microstructure, and quality of 316L stainless steel prepared by selective laser melting

Simulation and experimental studies on process parameters, microstructure and mechanical properties of selective laser melting of stainless steel 316L

Investigation into the effect of process parameters on microstructural and physical properties of 316L stainless steel parts by selective laser melting

Effect of selective laser melting (SLM) process parameters on microstructure and mechanical properties of 316L austenitic stainless steel

Study on performance optimization of 316L stainless steel parts by High-Efficiency Selective Laser Melting

The effect of selective laser melting process parameters and remelting scanning strategy on relative density and surface hardness of stainless steel 316L

Effects of laser scanning speed on the microstructure and mechanical properties of 2205 duplex stainless steel fabricated by selective laser melting

Influence of the Processing Parameters on the Microstructure and Mechanical Properties of 316L Stainless Steel Fabricated by Laser Powder Bed Fusion

Experimental Characterization and Strengthening Mechanism of Process-Structure-property of Selective Laser Melted 316 L

Comprehensive Investigation of the Mechanical Properties of 316L Stainless Steel Processed via Laser Powder Bed Fusion

Structural and micromechanical properties of 316L stainless steel produced by selective laser melting

Effect of Different Molding Process on Mechanical Properties of 316L Stainless Steel

Effect of Molten Pool Overlap on Mechanical Properties and Microstructure in Selective Laser Melting AISI 316L SS

Effect of laser scanning angle on shear slip behavior along melt track of selective laser melted 316L stainless steel during tensile failure

Experimental Characterization and Yield Strength Model for Process-Structure-Property of Selective Laser Melted 316L

Microstructure and dynamic-mechanical property of a selective laser melting AISI 316 L stainless steel

Molten pool effect on mechanical properties in a selective laser melting 316 L stainless steel at high-velocity deformation

Selective laser melting (SLM) of AISI 316L—impact of laser power, layer thickness, and hatch spacing on roughness, density, and microhardness at constant input energy density

Mechanical properties of 316L stainless steel samples fabricated by selective laser melting and comparison with other manufacturing methods

Effect of scanning speed on fatigue behavior of 316L stainless steel fabricated by laser powder bed fusion

A comprehensive study on microstructure and tensile behaviour of a selectively laser melted stainless steel