Abstract:Previous research often failed to prepared polymer-derived SiOC ceramic components with dense and thick monoliths/skeletons based on additive manufacturing processes, due to the porosities and cracks generated during the pyrolysis process. Herein, we report a simple solution which combines the introduction of phenolic resin (PR) as an additive and the use of controlled strategy of pyrolysis, for the vat photopolymerization additively manufactured SiOC ceramics. As a result, crack-free dense monolith and lattice skeleton structural polymer-derived SiOC ceramics are successfully prepared despite the low ceramic yield of 19.3 wt% and large linear shrinkage of 50% generated after pyrolysis. The prepared dense monoliths possess a thickness of over 5 mm and the lattices show attainable maximum dense skeletons thickness of ~2 mm. The maximum dense thickness of the samples after pyrolysis is over 7 times that of other samples prepared based on additive manufacturing reported in the literature. As an indicator of dimensional retention, the specific dense thickness to ceramic yield ratio (T/Y) is deduced, resulting maximum values of 101.9 μm/(wt%) for lattice skeletons and 254.7 μm/(wt%) for monoliths. The former is even larger than that for dense monolith SiOC structures prepared by other conventional gel casting and isostatic pressing techniques with much higher ceramic yields of > 80 wt%, and is about 6.1 times the largest T/Y ratio (=16.7 μm/(wt%)) achievable in the AM-based works reported in the literature. This shows predominance of the current work over other types of polymer-derived ceramic structures prepared by additive manufacturing and even conventional methods. The lattice structures’ apparent density and specific strength reached 0.55 g/cm3 and 6.6 × 104 N∙m/kg, respectively. The mechanical performance surpasses other structural polymer-derived ceramic structures with similar apparent density reported in the literature. Through the advanced characterization and analysis of material phase and morphology evolution during the pyrolysis process, the mechanism of defect-free densification is revealed. That is, the introduction of PR enables a highly smooth gas-releasing process due to the generation of ordered gas-releasing channels in the sample bodies during the pyrolysis process. As a result, the generation of cracks and defects was successfully prevented. Moreover, due to the high carbon residue of the PR, the samples containing 15 wt% PR in the preceramic state still possessed amorphous SiOC ceramics after pyrolysis at 1400 °C, while 0 wt% PR samples showed SiC crystallization. Compared with similar materials reported, the ceramics prepared in this study exhibit enhanced structural and mechanical performance. The strategy investigated in the study can be a viable route for the additive manufacturing of high-performance crack-free and thick monolith and lattice skeleton SiOC ceramic structures based on vat photopolymerization.

Effect of Polystyrene Addition on Properties of Porous Si3N4 Ceramics Fabricated by Digital Light Processing

Influence of the content of polymethyl methacrylate on the properties of porous Si3N4 ceramics fabricated by digital light processing

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

Microstructure and properties of porous Si 3 N 4 ceramics fabricated by digital light processing combined with spark plasma sintering

Influence of the Dispersants and Sintering Process on the Properties of Si2N2O Ceramics Via Digital Light Processing

Influence of the ratio of sintering aids on the properties of porous Si3N4 ceramics fabricated by digital light processing

Preparation and properties of Si3N4 ceramics via digital light processing using Si3N4 powder coated with Al2O3-Y2O3 sintering additives

Digital Light Processing of High-Strength Si3N4 Ceramics: Role of Particle Grading on Slurries Curing and Mechanical Properties

Porous Si3N4 ceramics with hierarchical pore structures prepared by gelcasting using DMAA as gelling agent and PS as pore–forming agent

Impact of Sintering Aid Type and Content on the Mechanical Properties of Digital Light Processing 3D-Printed Si3N4 Ceramics

Preparation and optimization of silicon nitride slurries for digital light processing

Digital light processing fabrication of porous cordierite ceramics from polysilxoane-based slurries

Digital Light Processing 3D Printing of Surface-oxidized Si3N4 Coated by Silane Coupling Agent

Enhanced Molding and Mechanical Properties of SiC-based Ceramic Lattice Structures Via Digital Light Processing

Preparation of porous Si 3 N 4 ceramics via tailoring solid loading of Si 3 N 4 slurry and Si 3 N 4 poly-hollow microsphere content

Effects of Organic Additives on Microstructure and Mechanical Properties of Porous Si 3 N 4 Ceramics

3D printing of crack-free dense polymer-derived ceramic monoliths and lattice skeletons with improved thickness and mechanical performance

Selective laser sintering of porous Al2O3-based ceramics using both Al2O3 and SiO2 poly-hollow microspheres as raw materials

Formation mechanism of stereolithography of Si3N4 slurry using silane coupling agent as modifier and dispersant

Preparation of high performance dense Al 2 O 3 ceramics by digital light processing 3D printing technology

Fabrication and properties of alumina ceramics shaped by digital light processing as an additive manufacturing technology