Abstract:In order to implement numerical simulation of the thermal-mechanical behaviors in the nuclear fuel rods, a three-dimensional finite element model is established. The thermal-mechanical behaviors at the initial stage of burnup in both the pellet and the cladding are obtained. Comparison of the obtained numerical results with those from experiments validates the developed finite element model. The effects of the constraint conditions, several operation and structural parameters on the thermal-mechanical performances of the fuel rod are investigated. The research results indicate that: (1) with increasing the heat generation rates from 0.15 to 0.6 W/mm(3), the maximum temperature within the pellet increases by 99.3% and the maximum radial displacement at the outer surface of the pellet increases by 94.3%. And the maximum Mises stresses in the cladding all increase; while the maximum values of the first principal stresses within the pellet decrease as a whole; (2) with increasing the heat transfer coefficients between the cladding and the coolant, the internal temperatures reduce and the temperature gradient remains similar; when the heat transfer coefficient is lower than a critical value, the temperature change is sensitive to the heat transfer coefficient. The maximum temperature increases only 7.13% when h changes from 0.5 W/mm(2) K to 0.01 W/mm(2) K, while increases up to 54.7% when h decreases from 0.01 W/mm(2) K to 0.005 W/mm(2) K; (3) the initial gap sizes between the pellet and the cladding significantly affect the thermal-mechanical behaviors in the fuel rod; when the gap size varies from 0.03 mm to 0.1 mm, the highest temperature in the pellet increases by 19.7%, and the maximum first principal stress at the outer pellet surface decreases by 17.4%; it is critical to optimize the gap size in order to reduce the pellet-cladding mechanical interaction and avoid their contact at early stage. This study lays a foundation for the further research on the irradiation-induced mechanical behaviors in the fuel rods. (C) 2011 Elsevier Ltd. All rights reserved.

Numerical investigation on effects of fuel rod with different shapes of bow deformation on the subcooled boiling of coolant in a fuel assembly

Prediction of critical heat flux in rod bowing geometries by coupled subchannel analysis and mechanistic model

Numerical investigation on critical heat flux for 5 × 5 fuel assemblies with a wide range of working conditions

Numerical study of the flow and heat transfer characteristics within the annular fuel element with double-sided cooling

The numerical investigation of the thermal–hydraulic behavior in a 3 × 3 rod bundle with spacer grids

Three-dimensional FE analysis of the thermal-mechanical behaviors in the nuclear fuel rods

Simulating Fuel Assembly Bowing: A Neutron-Diffusion Method Based on Arbitrary Quadrilateral Node and Conformal Mapping Technique

Numerical Analysis of Effects of Vane Deflection Angle on Flow-Thermal Characteristics in a Fuel Rod Assembly

Numerical Simulation and Analysis on Thermal-hydraulic Behavior of Fuel Assembly for Sodium-cooled Fast Reactor

Subcooled Boiling-Induced Vibration of a Heater Rod Located Between Two Metallic Walls

Investigation of Bubble Interaction in a Temporal and Spatial Heat Flux Partitioning Model for Subcooled Flow Boiling

BEHAVIOR OF VAPOR BUBBLES GENERATED ON A SINGLE HEATER ROD PARTLY CONFINED BY METALLIC WALLS IN SUBCOOLED WATER

Study on the Prediction of DNB-Type Critical Heat Flux in Rod Bundle Under Motion Conditions

Numerical investigation on mixing performance in rod bundle with spacer grid based on anisotropic turbulent mixing model

An Experimental investigation of void fraction characteristics of Flow Boiling in a 5×5 rod bundle channel

Study on coupling effect of CRUD growth and heat transfer on fuel rod

CFD study of two-phase cross flow and heat transfer in sub-channels of pressurized water reactor fuel assemblies

Numerical analysis of flow-induced deflection of curved nuclear reactor fuel plates under high velocity flows

Numerical analysis on the coolant-flow and heat-transfer in the fuel assembly

Numerical Investigation on the Thermal-Hydraulic Characteristics near a Corroded Lower Head of the Reactor Vessel During IVR-ERVC

Effects of Particle Volume Fraction on the Macro-Thermo-Mechanical Behaviors in Plate-Type Dispersion Nuclear Fuel Elements