Abstract:This paper presents a low-power chopper-stabilized capacitively-coupled frontend amplifier with auxiliary-path-based input impedance ( ${Z} _{\mathbf {in}}$ ) boosting. In order to achieve a high ${Z} _{\mathbf {in}}$ , a low noise and a small chip area, techniques on both system level and circuit level are implemented. On the system level, small capacitors ( ${C} _{\mathbf {in}}$ = 0.5 pF, ${C} _{\mathbf {fb}}$ = 25 fF) are used with a biased pseudo-resistor ( ${R}$ = 2.5 $\text{G}\Omega $ ) fed back to an amplifier internal node. As a result, a high achievable ${Z} _{\mathbf {in}}$ and low high-pass corner frequency are achieved. On the circuit level, an input capacitance shielded current feedback (CSCF) topology achieving effective 10 fF ${C} _{\mathbf {amp}}$ is proposed as the core of the capacitive feedback amplifier in order not to increase the input noise. Moreover, the design space of auxiliary-path-based boosting is explored to obtain the optimal value of buffer bandwidth and auxiliary capacitor size to save power. The amplifier and its ${Z} _{\mathbf {in}}$ boosting circuit are implemented in a standard 55 nm CMOS process and characterized experimentally. Measurement results show that the proposed amplifier provides an input noise density of 50 nV/ $\surd $ Hz, and an integrated noise of $0.85~\mu $ Vrms in 200 Hz band. The ${Z} _{\mathbf {in}}$ is boosted to 1.92 $\text{G}\Omega $ at DC and 1.02 $\text{G}\Omega $ at 50 Hz with only $1.0~\mu \text{A}$ in each auxiliary path buffer. The amplifier also archives 77 dB CMRR and 76 dB PSRR while consuming $20.3~\mu \text{W}$ in total.

P‐1.16: Frontend Amplifier with Unipolar Oxide TFTs for Heart Rate Measurement

Oxide TFT Frontend Amplifiers for Flexible Sensing Systems

A Front-End Circuit With 16-Channel 12-Bit 100-Ksps Rc-Hybrid Sar Adc For Industrial Monitoring Application

A 10 kHz bandwidth low-power active negative feedback front-end amplifier based on unipolar IZO TFT technology

A Front-end Amplifier with Fast Reset Scheme for Capacitive Heart Rate Monitoring

A 2.1/5.2-NEF/PEF Capacitively Coupled Instrumentation Amplifier with Fast - Settling for Biosensor

An Integrated Analog Front-End System on Flexible Substrate for the Acquisition of Bio-Potential Signals

A 20.3μw 1.9GΩ Input Impedance Capacitively-Coupled Chopper-Stabilized Amplifier for Bio-Potential Readout.

Ultra-High Input Impedance, Low Noise Integrated Amplifier for Noncontact Biopotential Sensing

A CMOS Physiological Monitoring Frontend for Wearable Health Applications

Design of an Analog Front-End for Ambulatory Biopotential Measurement Systems

A 20.3$\mu $W 1.9G$\Omega $ Input Impedance Capacitively-Coupled Chopper-Stabilized Amplifier for Bio-Potential Readout

A Novel High Input Impedance Front-End for Capacitive Biopotential Measurement

A 2.3-5.7μW Tri-Modal Self-Adaptive Photoplethysmography Sensor Interface IC for Heart Rate, SpO2, and Pulse Transit Time Co-Monitoring

A Compact Sub-μW CMOS ECG Amplifier With 57.5-MΩ Zin, 2.02 NEF, 8.16 PEF and 83.24-dB CMRR

Bio-Potential Sensing System With Monolithically Integrated Electrode Array and Analog Front-Ends on a Flexible Substrate

A 1.7μW/Channel Time-Division-Multiplexing Analog Front-End for Bio-Potential Recording

A low power analog front-end for portable biopotential acquisition systems

A Low Power Low Noise Front End Amplifier for ECG Monitoring

A 3.6 Μw 60 Nv/sqrthz Capacitively-Coupled Instrumentation Amplifier for Biopotential Signal Recordings.

3.10 A 0.69/0.58-PEF 1.6nW/24nW Capacitively Coupled Chopper Instrumentation Amplifier with an Input-Boosted First Stage in 22nm/180nm CMOS.