Abstract:Abstract The use of dry electrodes is increasing rapidly. Since their impedance is high, there is a high impedance node at the connecting node between the electrode and amplifier. This leads to absorb powerline signal and high CMRR amplifiers are essential to eliminate this. In this article, we propose a low-power low-noise chopper-stabilized amplifier with high CMRR. In order to minimise the input-referred noise, an inverter-based differential amplifier is utilized. Meanwhile, a DC servo loop is designed to reject the DC offset of the electrode. Since all of the stages required a common-mode feedback, for each of the amplifiers a suitable circuit was used. Furthermore, a chopping spike filter is implemented at the final stage to attenuate the choppers’ spike. Finally, to eliminate the offset effect from the mismatch and post-layout, a DC offset rejection technique is used. The designed circuit is simulated in a standard 180 nm CMOS technology. The designed chopper amplifier consumes just 1.1 $$\upmu \hbox {W}$$ μ W at a 1.2 $$\hbox {V}$$ V supply. The mid-band gain is 40 dB while the bandwidth is from 0.5 to 200 Hz. The total input-referred noise is 1 $$\upmu \hbox {V}_{\mathrm{rms}}$$ μ V rms in its bandwidth. Thus the NEF and PEF of the designed circuit is 2.7 and 9.7, respectively. In order to analyse the performance of the proposed chopper amplifier against process and mismatch variation, Monte Carlo simulation is done. According to 200 Monte Carlo simulations, CMRR and PSRR are 124 dB with 6.9 dB standard deviation and 107 dB with 7.7 standard deviation, respectively. Ultimately, the total area consumption is 0.1 $$\hbox {mm}^2$$ mm 2 without pads.

A Compact Sub-μW CMOS ECG Amplifier With 57.5-MΩ Zin, 2.02 NEF, 8.16 PEF and 83.24-dB CMRR

A compact, fully differential D-band CMOS amplifier in 65nm CMOS

A 20 Μw Dual-Channel Analog Front-End in 65nm CMOS for Portable ECG Monitoring System

A Low Power Low Noise Front End Amplifier for ECG Monitoring

An Inductorless 5-GHz Differential Dual Regulated Cross-Cascode Transimpedance Amplifier using 40 nm CMOS

A High DR High-Input-Impedance Programmable-Gain ECG Acquisition Interface with Non-inverting Continuous Time Sigma-Delta Modulator

A 7.5Gω-Input-impedance 109Db-Total-cmrr and 80Vpp-Cmi-tolerance Instrumentation Amplifier for Dry-Contact Two-Electrode ECG Monitoring

A Capacitive-Feedback Amplifier with 0.1% THD and 1.18 μVrms Noise for ECG Recording

A Novel Differential Log-Companding Amplifier for Biosignal Sensing

A fully differential capacitively-coupled high CMRR low-power chopper amplifier for EEG dry electrodes

A 2-Electrode ECG Amplifier with 0.5% Nominal Gain Shift and 0.13% THD in a 530mvpp Input Common-Mode Range

A 0.6V 119 dB High-CMRR Low-NEF PGA with common-mode voltage control for ECG recording

A low-noise CMOS front-end amplifier based on auto correction feedback for biomedical systems

A 4-Μw Analog Front End Achieving 2.4 NEF for Long-Term ECG Monitoring

A 0.6V 3.8μw ECG/bio-impedance Monitoring IC for Disposable Health Patch in 40nm CMOS

A Low-Power Low-Noise Amplifier for EEG/ECG Signal Recording Applications

Ultra-High Input Impedance, Low Noise Integrated Amplifier for Noncontact Biopotential Sensing

Micro-Power Low-Offset Instrumentation Amplifier IC Design for Biomedical System Applications

Design and Analysis of a High-Gain, Low-Noise, and Low-Power Analog Front End for Electrocardiogram Acquisition in 45 nm Technology Using gm/ID Method

A 15.5-ENOB 335mVPP-Linear-Input-Range 4.7GΩ-Input-Impedance CT-ΔΣM Analog Front-End With Embedded Low-Frequency Chopping

A 11GΩ-Input-Impedance 700mV<inf>pp</inf>-Input-Signal- Range 87dB-SNDR Direct-Digitization AFE for Wearable EEG Recording