Abstract:This article describes an ultra-high input-impedance active electrode (AE) circuit and the system to sense biopotential signals through a capacitively coupled interface. Various techniques from both circuit and system aspects are used to eliminate the input parasitic capacitance of the AE. On-chip parasitic capacitance is compensated by an auto-calibrated positive feedback loop (PFL) without applying any reference signal. A capacitor down-scaling technique combined with SAR-assisted PFL calibration enables femtofarad-level resolution of the capacitor array, alleviating the practical constraints of the conventional PFL to implement a small capacitor below 10 fF. Besides, a dummy input structure ensures that the pad and electrostatic discharge (ESD) capacitances are also canceled by the PFL, while off-chip parasitic capacitance on the printed circuit board (PCB) is nulled by active shielding. Fabricated in a standard 0.18- $\mu$ m 1P6M CMOS process, the AE achieves an ultra-high input impedance of 136 G $\Omega$ at 60 Hz (average of 10 samples). This is equivalent to an input capacitance of 19.5 fF and corresponds to a 2.7 $\times$ –68 $\times$ improvement over the state-of-the-art. The AE exhibits an input signal range of 700 mV $_{\mathrm{pp}}$ and an input-referred noise of 0.72 $\mu $ V $_{\mathrm{rms}}$ (0.5–100 Hz) while consuming 10.46 $\mu $ W from a 1.2-V supply. Each AE integrates an IC and a 3-cm $^{2}$ copper electrode on the PCB, and the wearable system prototypes successfully measured high-quality electrocardiogram (ECG) and electroencephalogram (EEG) signals from test subjects through capacitively coupled interfaces.

Ultra-High Input Impedance, Low Noise Integrated Amplifier for Noncontact Biopotential Sensing

A 2.1/5.2-NEF/PEF Capacitively Coupled Instrumentation Amplifier with Fast - Settling for Biosensor

A 136-GΩ Input-Impedance Active Electrode for Non-Contact Biopotential Signals Monitoring

A Novel High Input Impedance Front-End for Capacitive Biopotential Measurement

High Input Impedance Low-Noise CMOS Analog Frontend IC for Wearable Electrocardiogram Monitoring

A 400 GΩ Input-Impedance Active Electrode for Non-Contact Capacitively Coupled ECG Acquisition with Large Linear-Input-Range and High CM-Interference-Tolerance

Low Noise, High Input Impedance Digital-Analog Hybrid Offset Suppression Amplifier for Wearable Dry Electrode ECG Monitoring

High-Input-Impedance Amplifiers Design for Dry-Electrode Biopotential Acquisition: A Review

Design of Ultra-Low Power Biopotential Amplifiers for Biosignal Acquisition Applications

A 382nVrms 100GΩ@50Hz Active Electrode for Dry-Electrode EEG Recording

A 35 nV/√Hz Analog Front-End Circuit with Adjustable Bandwidth and Gain in UMC 40 nm CMOS for Biopotential Signal Acquisition

A Front-end Amplifier with Fast Reset Scheme for Capacitive Heart Rate Monitoring

A 20.3μw 1.9GΩ Input Impedance Capacitively-Coupled Chopper-Stabilized Amplifier for Bio-Potential Readout.

A low power analog front-end for portable biopotential acquisition systems

A Low Power Low Noise Front End Amplifier for ECG Monitoring

A Fully Integrated Chopper IA for Implantable Multichannel EEG Recording Without Impedance Boosting Circuits

A $64.8~\mu$ W > 2.2 G $\omega$ DC–AC Configurable CMOS Front-End IC for Wearable ECG Monitoring

A 3.6 Μw 60 Nv/sqrthz Capacitively-Coupled Instrumentation Amplifier for Biopotential Signal Recordings.

A Noncontact ECG Sensing System With a Micropower, Ultrahigh Impedance Front-End, and BLE Connectivity

A 0.5-Mω/√hz Dry-Electrode Bioimpedance Interface with Current Mismatch Cancellation and Input Impedance of 100 MΩ at 50 Khz.

A 136G-Input-Impedance Active Electrode for Non-Contact ECG Using Auto-Calibrated. Positive Feedback and Capacitance Scaling in Femtofarad Resolution