Abstract:The micro-texture is a relatively well-established method for improving the tribological performance of Co-Cr-Mo alloy. Currently, to fabricate the micro-textures on the alloy surface, laser micromachining technology is the commonly used method. However, the low fabrication quality (such as irregular protrusions inside and on the edges of the micro-textures) caused by laser ablation limits the numerous application of laser surface textures. Therefore, a novel method of combining nanosecond (ns) pulse laser texturing with ion beam etching was proposed to prepare the micro-textures on the surface of Co-Cr-Mo alloy. The tribological properties before and after ion beam etching were tested by ball-disk friction wear test for three different micro-texture morphologies (grooved micro-texture (G); hexagonal micro-texture (H); concentric micro-texture (C)), and the micro-topography, mechanical properties and wettability of the ion beam/laser textured Co-Cr-Mo alloy were also investigated. The results showed that the friction coefficient and wear amount of the specimen surface were reduced after ion beam etching, and the ion beam/laser textured sample with hexagonal micro-textures showed the best wear performance, with the average friction coefficient reduced by 11.9 % and the wear amount of polyether ether ketone balls reduced by 14.9 %. The worn surface of the ion beam etched samples was relatively smooth, and the adhesive wear was also reduced. This report established the friction reduction model of ion beam/laser textured alloy and revealed the friction reduction mechanism of ion beam etching, providing a new idea of fabricating high-quality micro-textures to enhance the wear performance of artificial hip joints.

Improving Tribological Behaviors of Invar 36 Alloy under Extremely Cryogenic and Dry Conditions Through Surface Micro-Texturing

Microstructure Evolution and Corrosion Behavior of Invar 36 Alloy Additively Manufactured Via Laser Powder Bed Fusion

Effect of Processing Parameters on the Microstructure, Mechanical Properties and Thermal Expansion Behavior of Invar 36 Alloy Manufactured by Laser Powder Bed Fusion

Research on Improving the Tribological Properties of Bearings under Cryogenic Conditions

Improving the Tribological Properties of WE43 and WE54 Magnesium Alloys by Deep Cryogenic Treatment with Precipitation Hardening in Linear Reciprocating Motion

Additional Tribological Effect of Laser Surface Texturing and Diamond-Like Carbon Coating for Medium Carbon Steel at Near Room Temperature

High-temperature tribological properties of AlCrN coatings deposited on textured surfaces under dry friction

Combined Effect of a Laser Cladded Coating and Surface Texture on Tribological Performance Under Dry Sliding and Starved Lubrication

Contact and Tribological Study of Micro/Nano Groove Texture on the Surface of Gas Bearing Materials Based on Nanoscale

Enhancing tribological performance in PM Vanadis 6 steel through optimization of cryogenic and tempering treatment

Ultra-low wear of titanium alloy surface under lubricated conditions achieved by laser texturing and simultaneous nitriding

Effect of ion beam etching on the tribological performance of laser textured Co-Cr-Mo alloy

Cryogenic tribological behavior of coarse, ultrafine grained and heterogeneous Fe-18Cr-8Ni austenitic stainless steel

Wear-resistant CoCrNi multi-principal element alloy at cryogenic temperature

Tool Wear and Surface Integrity of γ-TiAl Cryogenic Coolant Machining at Various Cutting Speed Levels

Tribological behavior of WC-6Co against Ti–6Al–4V alloy under novel cryogenic ethanol-ester oil dry-ice hybrid lubri-cooling

Investigation of the preparation and tribological behavior of a frictional interface covered with sinusoidal microchannels containing SnAgCu and Ti3SiC2

Relationship between discoloration, condensation, and tribology behavior of steel surfaces at cryogenics in vacuum

Effects of Deep Cryogenic Treatment on Tribological Properties of the Tool Steel DC53

Tribological Properties of Groove-Textured Ti-6Al-4V Alloys with Solid Lubricants in Dry Sliding against GCr15 Steel Balls

Tribological Properties of Ti6Al4V Alloy Composite Texture Fabricated by Ultrasonic Strengthening Grinding and Laser Processing