Abstract:It is a well-known fact that the consumption of conventional cutting fluids in metalworking industries leads to severe health and environmental issues. Owing to the EPA (Environmental Protection Agency) increasing regulations regarding pollution and contamination, there is a dire need for a greener fluid with excellent cooling and lubrication characteristics to diminish the environmental impact of cutting fluids, as well as to improve machinability. Cryogens are greener and excellent coolants but poor lubricants, while ester oils are excellent lubricants and poor coolants. Therefore, a hybrid lubri-coolant cutting fluid with synergistic cooling and lubrication characteristics could be a desideratum to replace conventional cutting fluid. To investigate a newly proposed hybrid lubri-coolant, thermophysical properties (density, thermal conductivity, specific heat, and viscosity), heat transfer properties (surface temperature, heat flux, and heat transfer coefficient), and machinability properties (tool life, etc.) are key characteristics of the fluids that decide phase change and heat dissipation capabilities during their application in machining. In the current experimental study, hybrid ethanol–ester oils with/without dry ice (−78 °C) are proposed as cutting fluids and holistically investigated in terms of thermo-physical properties, heat transfer properties, and machinability properties under different cutting conditions. Experimental findings have depicted a 20%, 10%, and 5% decrease in density, specific heat, and viscosity, respectively, with a 15% increase in the thermal conductivity of the fluid with the addition of dry ice. The dry-ice-based hybrid lubri-coolant sprayed onto a Ti-6Al-4V plate enhanced the heat transfer coefficient significantly by 17% compared to hybrid lubri-coolant without dry ice. Besides, hybrid ethanol–ester oil dry ice was treated as a trendsetter and indicated an 11% improvement of the tool life at a cutting speed of 75 m/min and a feed rate of 0.04 mm/z. Therefore, dry-ice-based hybrid lubri-coolant can be applied as a cutting fluid by practitioners in aerospace, automotive, prosthetic body parts manufacturing, and manufacturing industries.

Tribological behavior of WC-6Co against Ti–6Al–4V alloy under novel cryogenic ethanol-ester oil dry-ice hybrid lubri-cooling

Tool wear mechanisms and its influence on machining tribology of face milled titanium alloy under sustainable hybrid lubri-cooling

Tribological behavior of modified polyetheretherketone composites in sliding against stainless steel under water lubrication

Thermophysical, tribological, and machinability characteristics of newly developed sustainable hybrid lubri-coolants for milling Ti-6Al-4V

Thermophysical Properties and Heat Transfer Performance of Novel Dry-Ice-Based Sustainable Hybrid Lubri-Coolant

Tribological properties and tool wear in milling of in-situ TiB2/7075 Al composite under various cryogenic MQL conditions

Characterization of friction behavior under cryogenic conditions: Ti–6Al–4V

Cooling/Lubrication Performance of Dry and Supercritical CO2-Based Minimum Quantity Lubrication in Peripheral Milling Ti-6Al-4V

The Tribological Behavior of Ni–Cu–Ag-based PVD Coatings for Hybrid Bearings under Different Lubrication Conditions

Friction and Wear Performance of Titanium Alloys against Tungsten Carbide under Dry Sliding and Water Lubrication

Studies on newly developed hBN/graphene-based nano-fluids supported by cryogenic cooling conditions in improving the tribological performance of Ti6Al4V alloy

Heat Transfer Efficiency of Cryogenic-LN2 and CO2-snow and their application in the Turning of Ti-6AL-4V

Tribology and machinability performance of hybrid Al2O3 -MWCNTs nanofluids-assisted MQL for milling Ti-6Al-4 V

On tribological characteristics of TiC rollers machined under hybrid lubrication/cooling conditions

Study On The Tribological Properties Of Titanium Alloys Sliding Against Wc-Co During The Dry Friction

Tribological Properties of Titanium Alloys under Lubrication of SEE Oil and Aqueous Solutions

Progresses on Cryo-Tribology: Lubrication Mechanisms, Detection Methods and Applications

Wear performance of Ti-6Al-4 V titanium alloy through nano-doped lubricants

A Novel Use of Hybrid Cryo-MQL System in Improving the Tribological Characteristics of Additively Manufactured 316 Stainless Steel against 100 Cr6 Alloy

Influence of CO2-snow and subzero MQL on thermal aspects in the machining of Ti-6Al-4V

Friction and wear behaviors of the carbide tools embedded with solid lubricants in sliding wear tests and in dry cutting processes