Abstract:Hard turns in machining present substantial obstacles to chip removal. An effective heat management system is needed to avoid tool overheating and reduce cutting capacity. Therefore, the present investigates the effectiveness of a comparative study of four cooling methods, such as dry turning, minimum quantity lubrication (MQL), cryogenic (LN2), and the hybrid Cryo-nMQL approach, on machining performance during the machining of SS904L alloy. Machining conditions included 75 and 150 m/min cutting velocities and feed rates of 0.1 and 0.2 mm/rev, respectively. Results indicate that cryo-nMQL exhibited superior performance matched to the other cooling methods, with a maximum improvement of surface roughness by 57.73% and nose wear by 13.87%, flank wear by 67.48%, crater wear by 8.42%. In addition, chip production indicates a fine lamella structure with less serration under cryo-nMQL. In addition, the combination of cryo-nMQL resulted in enhanced tool life and a notable decrease in tool wear with a research gap, indicating future work to assess the benefits of hybrid cooling methods in SS904L machining, thereby showcasing the potential of these innovative technologies in mechanical engineering applications. Les virages durs en usinage présentent des obstacles importants à l'évacuation des copeaux. Un système de gestion thermique efficace est nécessaire pour éviter la surchauffe des outils et la réduction de la capacité de coupe. Par conséquent ce travail examine l'efficacité d'une étude comparative de quatre méthodes de refroidissement, telles que le tournage à sec, la lubrification minimale (MQL), la cryogénie (LN2) et l'approche hybride Cryo-nMQL, sur les performances d'usinage lors de l'usinage de l'alliage SS904L. Les conditions d'usinage comprenaient des vitesses de coupe de 75 et 150 m/min et des vitesses d'avance de 0.1 et 0.2 mm/tr, respectivement. Les résultats indiquent que le cryo-nMQL démontrait des performances supérieures à celles des autres méthodes de refroidissement, avec une amélioration de la rugosité de la surface de 57.73% et de l'usure du bec de 13.87%, de l'usure des flancs de 67.48%, et de l'usure du cratère de 8.42%. De plus, la production de copeaux indique une structure lamellaire fine avec moins de cannelures sous cryo-nMQL. De plus, la combinaison cryo-nMQL a amené une amélioration de la tenue des outils et une baisse notable de l'usure des outils avec une lacune dans la recherche, ce qui indique des travaux futurs pour évaluer les avantages des méthodes de refroidissement hybrides dans l'usinage de SS904L, mettant ainsi en valeur le potentiel de ces technologies innovantes dans les applications en génie mécanique.

Influence of hybrid Cryo-MQL lubri-cooling strategy on the machining and tribological characteristics of Inconel 718

Tool wear mechanisms and its influence on machining tribology of face milled titanium alloy under sustainable hybrid lubri-cooling

Investigations on pulsed and continuous supply of a cryogenic medium in milling of Waspaloy and Inconel 718 under various lubri-cooling environments

Machining performance of Inconel 718 in dry, air-cooling and bio-oil based minimum quantity lubrication environments

Machinability analysis of dry and liquid nitrogen–based cryogenic cutting of Inconel 718: experimental and FE analysis

Investigation of machinability in milling of Inconel 718 with solid Sialon ceramic tool using supercritical carbon dioxide (scCO<sub>2</sub>)-based cooling conditions

Investigation of machining performance in SS904L alloy under hybrid cooling conditions

Tool wear patterns and their promoting mechanisms in hybrid cooling assisted machining of titanium Ti-3Al-2.5V/grade 9 alloy

Application of minimum quantity GnP nanofluid and cryogenic LN 2 in the machining of Hastelloy C276

Investigation of the Effects of Cooling and Lubricating Strategies on Tribological Characteristics in Machining of Hybrid Composites

Evaluation of minimum quantity lubrication effects by cutting force signals in face milling of Inconel 182 overlays

Evaluation of Surface Roughness, Tool Wear and Chip Morphology during Machining of Nickel-Based Alloy under Sustainable Hybrid Nanofluid-MQL Strategy

A Novel Use of Hybrid Cryo-MQL System in Improving the Tribological Characteristics of Additively Manufactured 316 Stainless Steel against 100 Cr6 Alloy

Novel use of cryogenic cooling conditions in improving the machining performance of Al 8011/nano-SiC composites

Employing Preheating- and Cooling-Assisted Technologies in Machining of Inconel 718 with Ceramic Cutting Tools: Towards Reducing Tool Wear and Improving Surface Integrity

The Effects of Cryogenic Cooling on Tool Wear and Chip Morphology in Turning of Tantalum-Tungsten Alloys Ta-2.5W

Wear mechanisms and cutting performance of coated carbides in milling LPBF IN718 alloy under hybrid cryogenic conditions

Tribology and machinability performance of hybrid Al2O3 -MWCNTs nanofluids-assisted MQL for milling Ti-6Al-4 V

Prediction Model for Specific Cutting Energy of Nickel-Based Inconel 718 under NMQL Condition

Tribological properties and tool wear in milling of in-situ TiB2/7075 Al composite under various cryogenic MQL conditions

Comprehensive investigation of the effect of cryogenic process on machining of Inconel 718 superalloys with uncoated end mills