Abstract:Pressure swing adsorption (PSA) appears to be an effective technology for biogas upgrading under different operating conditions with low greenhouse gas emissions. This study presents the simulation of biomethane adsorption with the adsorption bed filled with a carbon molecular sieve (CMS). A six dual-bed six-step PSA process was studied which produced a high purity of biomethane. The design of the adsorption bed was followed by the real process of which the biomethane capacity was more than 5000 Nm3/h. For the adsorbent, a CMS-3K was used, and a biomethane gas with a minimum 92% purity was produced at 6.5 bar adsorption pressure. To understand the adsorption characteristics of the CH4 and CO2 gases, the Langmuir isotherm model was used to determine the isotherm of a mixed gas containing 55% CH4 and 45% CO2. Furthermore, the experimental data from the work of Cavenati et al. were used to investigate the kinetic parameter and mass transfer coefficient. The mass transfer coefficients of two species were determined to be 0.0008 s−1 and 0.018 s−1 at 306 K for CH4 and CO2, respectively. The PSA process was then simulated with a cyclic steady state until the relative tolerance was 0.0005, which was then used to predict the CH4 and CO2 mole fraction along the adsorption bed length at a steady state. Moreover, the optimal conditions were analyzed using Aspen Adsorption to simulate various key operating parameters, such as flowrate, adsorption pressure and adsorption time. The results show a good agreement between the simulated results and the real operating data obtained from the company REBiofuel. Finally, the sensitivity analysis for the major parameters was presented. The optimal conditions were found to be an adsorption pressure of 6 bar, an adsorption time of 250 s and a purity of up to 97.92% with a flowrate reducing to 2000 Nm3/h. This study can serve as a commercial approach to reduce operating costs.

Pressure Swing Adsorption Process Simulation for Recover High Purity Ethylene Product

Modelling and Simulation of Two-Bed PSA Process for Separating H2 from Methane Steam Reforming

Strategy of Effluent Recovery Technology Selection in Polyolefin Plants

[Recovery of CO from an Ammonia Plant Tail Gas with Pressure Swing Adsorption Process].

Simulation and Energy Consumption Comparison of Gas Purification System Based on Elevated Temperature Pressure Swing Adsorption in Ammonia Synthetic System

Simulation of H_2-Recovery for PSA Process in Indirect Coal Liquefaction System

A Systematic Simulation and Proposed Optimization of the Pressure Swing Adsorption Process for N2/CH4 Separation under External Disturbances

Nitrogen rejection from low quality natural gas by pressure swing adsorption experiments and simulation using dynamic adsorption isotherms

State-of-the-art in Applications of Pressure Swing Adsorption Technology

Ethylene Purification by Pressure Swing Adsorption with the Paraffin Selective Metal–Organic Framework─DUT-8

Study of Modeling for Fixed-Bed Adsorption Process and Simulation in Experimental CO Separation Through PSA

Heat Integrated Technology Assisted Pressure-Swing Distillation for the Mixture of Ethylene Glycol and 1,2-Butanediol

Simulation of Distillation Based on Aspen Plus for Products from Catalytic Amination of Ethanolamine

Simulation and experiment for the pressure swing adsorption separation of methane and nitrogen

Application analysis of layered pressure swing adsorption method for offshore floating natural gas purification

Pilot-scale Experiment for Purification of CO from Industrial Tail Gases by Pressure Swing Adsorption

Techno-economic Evaluation of an Elevated Temperature Pressure Swing Adsorption Process in A 540 MW IGCC Power Plant with CO2 Capture

Essence of Pressure Swing Adsorption

Separation of Ethylene and Ethane Using Co-Gallate Pellets in a Vacuum Swing Adsorption Process

Optimization of a Six-Step Pressure Swing Adsorption Process for Biogas Separation on a Commercial Scale

Separation of Methane and Nitrogen Using Heavy Reflux Pressure Swing Adsorption: Experiments and Modeling