Abstract:Meso-structural models are presently in common use for analysis of the mechanical behaviour, damage evolution and failure of concrete. These are constructed either from XCT images, or in silico, using statistical information about concrete's meso-scale constituents. As a minimum, such models include mortar and aggregates as separate phases, while more detailed versions consider the interfacial transition zones (ITZ) between mortar and aggregates, and voids. Analyses of given meso-structures vary further by different constitutive modelling of constituents, with past works focusing on parameters' calibration using experiments with one loading condition - either tension or compression. Using a detailed meso-structure representation, this work proposes a novel combination of constitutive relations, involving concrete damage plasticity (CDP) for mortar and cohesive zone behaviour for ITZ. CDP parameters are calibrated using both compression and tension experiments with mortar samples. ITZ parameters are calibrated by comparing simulated stress–strain curves and failure patterns with data from compression and tension experiments with concrete samples. This process leads to constitutive relations, applicable to both loading conditions, which has not been demonstrated previously, but is essential to extending the modelling approach to complex stress states encountered in real engineering structures. After establishing the realism of the approach, parametric studies are conducted to investigate the effects of friction between loading plate and specimen, the mortar dilation angle, the ITZ cohesive stiffness, critical stresses, fracture energy and mix mode ratio. The results show that mortar plasticity is the dominant energy dissipation mechanism in both compression and tension, and its rate governs the localisation of damage. The effect of ITZ parameters on the tensile behaviour is found to be negligible. Their effect on the compressive behaviour is found to be limited, but sufficient to propose a set of parameters working for both conditions. Importantly, under both loadings the ITZ is found to control failure localisation into a macroscopic crack in combination with mortar plasticity and damage. Predicted stress-stain curves, damage evolution and macro-crack propagation are shown to be in very good agreement with the experimental observations. This justifies the use of the proposed experimental-modelling strategy for developing models for analysis of complex loading conditions.

Numerical Simulation on Damage Behaviors of Tile-Mortar Interface Induced by Mortar Shrinkage and Temperature Cycles

Temperature Fatigue Characteristics of Tile-Mortar Interface Based on Fatigue Cohesive Zone Model

Simulation and Experimental Verification of the Non-Uniform Corrosion Cracking Process of Reinforced Mortar Specimen

Numerical Study of Shrinkage Cracking in Concrete and Concrete Repair Systems

Change of the Coefficient of Thermal Expansion of Mortar Due to Damage by Freeze Thaw Cycles

A Mesoscale Modelling Approach Coupling SBFEM, Continuous Damage Phase-Field Model and Discrete Cohesive Crack Model for Concrete Fracture

Mesoscale Simulation of Deformation for Mortar and Concrete under Cyclic Freezing and Thawing Stress

Experimental and numerical investigation of mortar and ITZ parameters in meso-scale models of concrete

Damage and Degradation Mechanism for Single Intermittent Cracked Mortar Specimens under a Combination of Chemical Solutions and Dry-Wet Cycles

Mechanical properties of thermally damaged mortar under coupled static-dynamic loading

Meso-Scale Mechanical Deterioration Of Mortar Subjected To Freeze Thaw Cycles And Sodium Chloride Attack

Damage Based Constitutive Model for Predicting the Performance Degradation of Concrete

Numerical Analysis of Drying Shrinkage in Long Reinforced Concrete Structure

An elastic-plastic cohesive zone model for metal-ceramic interfaces at finite deformations

Numerical Simulation of Fracture and Damage Behaviour of Concrete at Different Ages

Mesoscale Simulation of Concrete Behavior with Non-Uniform Frost Damage with Verification by CT Imaging

Experimental and Numerical Investigation on the Tensile Fracture of Compacted Clay

Mesoscale analysis of dry shrinkage fractures in concrete repair systems using FEM and VEM

Drying shrinkage crack simulation and meso-scale model of concrete repair systems

Experimental Study of Micro/macro Crack Development and Stress–strain Relations of Cement-Based Composite Materials at Elevated Temperatures

A robust computational strategy for failure prediction of masonry structures using an improved multi‐surface damage‐plastic based interface model