Abstract:The mechanical properties of metallic matrix composites can be tailored through the microstructural modification between metal matrix and reinforcing particles. In this work, the AA2219/TiC nanocomposite containing 0, 0.5, 0.9, 1.3 and 1.7 wt.% TiC nanoparticles were individually manufactured using the ultrasound-assisted solidification technique. There existed an optimal addition level of TiC nanoparticles (0.9 wt.%) beyond which grain coarsening occurred. TiC nanoparticles were observed to reduce the average grain sizes of α-Al matrix alloy by 61%. Meanwhile, 0.9 wt.% TiC nanoparticles corresponded to the maximum tensile strength and hardness. When the addition level reached over 0.9 wt.% in the 2219 Al alloy matrix melt, the TiC nanoparticles tended to agglomerate in a form of condensed clusters, which cannot be well dispersed by ultrasonication due to the increasing viscosity. Such agglomerating TiC nanoparticles deteriorated the tensile strain and hardness of AA2219/TiC nanocomposite. Then, five major potential strengthening mechanisms in AA2219/TiC nanocomposite was quantitatively analysed, including grain refinement, Orowan strengthening, load transfer effect, mismatch of thermal expansion, and mismatch of elastic modulus. Analysis shows that Orowan strengthening acts as the most dominant strengthening mechanism, followed by another comparable strengthening mechanism from the mismatch between the thermal expansion of α-Al matrix and TiC nanoparticles. The other three strengthening mechanisms induced very limited improvement in mechanical properties. Besides acting as reinforcing agents, the TiC nanoparticles also possess very high potency as heterogeneous nucleation sites. The relevant nucleation potency was validated by crystallographic investigation using the edge-to-edge matching model. Finally, the grain refining mechanism of α-Al matrix alloy was unraveled in terms of the nucleation crystallography and the ultrasonic cavitation.

Nanostructure Evolution of Reticular Nano-Tib Whiskers Reinforced Titanium Matrix Composite Subjected to Ultrasonic Shot Peening

Nano-TiB Whiskers Reinforced Ti–6Al–4 V Matrix Composite Fabricated by Direct Laser Deposition: Microstructure and Mechanical Properties

Tailoring A Novel Network Reinforcement Architecture Exploiting Superior Tensile Properties of in Situ Tibw/Ti Composites

Microstructure and Wear-resistant Properties of in situ TiB-TiC Reinforced Titanium Matrix Composites by Laser Deposition Manufacturing

Effects of shot peening on microstructure evolution and mechanical properties of surface nanocrystal layer on titanium matrix composite

Microstructure Evolution and Numerical Modeling of TC4 Titanium Alloy during Ultrasonic Shot Peening Process

TiB Nano-Whiskers Reinforced Titanium Matrix Composites with Novel Nano-Reticulated Microstructure and High Performance Via Composite Powder by Selective Laser Melting

An innovative TiB whisker architecture of titanium matrix composite devised by scanning electron beam remodeling

Microstructure and Mechanical Properties Variation of Tib/Ti Matrix Composite by Thermo-Mechanical Processing in Beta Phase Field

Network structured nano-TiB/Ti composites coating on Ti64 alloy with improved wear properties by direct laser deposition

Superior superplasticity and multiple accommodation mechanisms in TiB reinforced near-α titanium matrix composites

Residual Stress Distribution And Microstructure Characterization Of Particle Reinforced Titanium Matrix Composite After Shot Peening Treatment: A Review

Improved Mechanical Properties in Titanium Matrix Composites: Controllable TiBw Distribution by Thermal Deformation Process

Microstructure Evolution, Hardness, and Tribological Behaviors of Ti-50.8Ni SMA Alloy with Ultrasonic Surface Shot Peening Treatment

Simultaneous Enhancements of Strength, Ductility, and Toughness in a TiB Reinforced Titanium Matrix Composite

The Mechanical Behavior Dependence on the TiB Whisker Realignment During Hot-Working in Titanium Matrix Composites

Effect of the Conventional Shot Peening and Multiple Shot Peening on Microstructure and Residual Stress of TC17 Titanium Alloy

Microstructural evolution and mechanical properties of the AA2219/TiC nanocomposite manufactured by ultrasonic solidification

Significantly Enhanced Superplasticity of TiBw/near-α Ti Composite: Microstructure Tailoring and Deformation Mechanisms

Ultrasound-assisted Dispersion of TiB2 Nanoparticles in 7075 Matrix Hybrid Composites

Molecular dynamics simulation of microstructural evolution and mechanical behavior of titanium alloy subjected to laser shock peening