Abstract:In this work, near-alpha Ti-6.5A1-2Zr-Mo-V alloys were successfully fabricated through Laser Powder Bed Fusion (LPBF) and subjected to post-heat treatments. A comparative study on the microstructure and mechanical properties of different samples was performed to reveal the effects of LPBF process parameters and post-heat treatments. The optimal LPBF process window for fabricating relative density > 99.9% samples is located in the volumetric energy density (VED) range of 125-167 J/mm(3). The extremely rapid cooling rate in LPBF induced a full martensite alpha' structure. Substructures characterized by low angle grain boundaries (LAGBs), tangled high angle grain boundaries (HAGBs), and several inter-variants were found in the as-built samples. In the optimal VED range, no significant microstructural difference among the samples was found. This resulted in a stable level of mechanical properties for the optimal as-built samples: 1172-1227 MPa in ultimate tensile strength (UTS), 7.9-8.8% in elongation, similar to 425 Hv in microhardness. After sub-beta heat treatments, the LPBF-induced substructures of LAGBs and HAGBs were gradually eliminated, resulting in a decrease in UTS but an increase in elongation. An increase of similar to 57 degrees boundaries was found in the HT700 and HT800 samples, suggesting a boundary transformation during the recrystallization. The transformation is beneficial to the mechanical property. It contributed to a small drop of UTS (similar to 20 MPa) for the HT700 and HT800 samples and significantly improved ductility compared with the as-built samples. The HT900 sample underwent complete recrystallization with an alpha-lath dominated structure. Thereby it exhibits a better ductility but a lower UTS compared with the HT700 and HT800 samples. After the super-beta heat treatments, a large amount of martensite reappeared. Due to the large size of prior 1 grains, the ductility was significantly decreased. The results of this study can be used to guide the adjustment of the microstructure of LPBF-processed Ti-6.5Al-2Zr-Mo-V alloy through post-heat treatments to obtain a good combination of tensile properties.

Process-microstructure-properties of CuAlNi Shape Memory Alloys Fabricated by Laser Powder Bed Fusion

Simultaneous enhancement of mechanical and functional properties by heat-treatment in CuAlNi shape memory alloys fabricated by laser powder bed fusion

Deformation Mechanism of Cu-Al-Ni Shape Memory Alloys Fabricated Via Laser Powder Bed Fusion: Tension-compression Asymmetry

Process Optimization, Microstructures and Mechanical Properties of a Cu-based Shape Memory Alloy Fabricated by Selective Laser Melting

Mechanical behavior and microstructure evolution of Al-Cu-Mg alloy produced by laser powder bed fusion: Effect of heat treatment

4D Forming Shape Memory Component of Cu–13Al–5Fe Alloy Based on Laser Powder Bed Fusion of Metal Powders

Achieving dual-phase structured Cu-Al-Mn-Si alloy with prominent shape memory properties via laser powder bed fusion

Achieving High Strength-Ductility Combination of Al-Mn-Mg-Sc-Zr Alloy Subjected by Laser Powder Bed Fusion and Suitable Post Heat Treatment

Shape Memory Effect Enhancement Via Aging Treatment of the Cu-Al-Mn-Si Alloy Manufactured Using Laser Powder Bed Fusion

Altered Microstructure, Phase Transformation Behaviors and Shape Memory Response of Cualmn Shape Memory Alloys Fabricated by Selective Laser Melting

Microstructural Evaluation and Tensile Properties of Al-Mg-Sc-Zr Alloys Prepared by LPBF

Unraveling Effect of Nb Addition on the Microstructure, Phase Transformation Behaviour and Shape Memory Effect of CuAlMn Alloy Fabricated by Laser Powder Bed Fusion

Development of Fe-Mn-Si-Cr-Ni Shape Memory Alloy with Ultrahigh Mechanical Properties and Large Recovery Strain by Laser Powder Bed Fusion

In-Situ Tailoring Microstructures to Promote Strength-Ductility Synergy in Laser Powder Bed Fusion of Nicocr Medium-Entropy Alloy

Effect of Solution Treatment on the Microstructure, Phase Transformation Behavior and Functional Properties of NiTiNb Ternary Shape Memory Alloys Fabricated Via Laser Powder Bed Fusion In-Situ Alloying

Microstructure and Mechanical Properties of Ti-6.5Al-2Zr-Mo-V Alloy Processed by Laser Powder Bed Fusion and Subsequent Heat Treatments

Tensile Deformation Behaviors of Laser Powder Bed Fusion Fabricated Al–Mn-Sc Alloy with Heterogeneous Grain Structure

Enhanced Mechanical Properties of the Additively Manufactured IN738LC Superalloy Through Thermal History Management During the Laser Powder Bed Fusion Process

Effect of Volume Energy Density on Selective Laser Melting Niti Shape Memory Alloys: Microstructural Evolution, Mechanical and Functional Properties

Formation Mechanism of Heterogeneous Microstructures and Shape Memory Effect in NiTi Shape Memory Alloy Fabricated Via Laser Powder Bed Fusion

Crack Inhibition and Mechanical Property Enhancement of a CM247LC Alloy Fabricated by Laser Powder Bed Fusion Through Remelting Strategy