Abstract:In this work, near-alpha Ti-6.5A1-2Zr-Mo-V alloys were successfully fabricated through Laser Powder Bed Fusion (LPBF) and subjected to post-heat treatments. A comparative study on the microstructure and mechanical properties of different samples was performed to reveal the effects of LPBF process parameters and post-heat treatments. The optimal LPBF process window for fabricating relative density > 99.9% samples is located in the volumetric energy density (VED) range of 125-167 J/mm(3). The extremely rapid cooling rate in LPBF induced a full martensite alpha' structure. Substructures characterized by low angle grain boundaries (LAGBs), tangled high angle grain boundaries (HAGBs), and several inter-variants were found in the as-built samples. In the optimal VED range, no significant microstructural difference among the samples was found. This resulted in a stable level of mechanical properties for the optimal as-built samples: 1172-1227 MPa in ultimate tensile strength (UTS), 7.9-8.8% in elongation, similar to 425 Hv in microhardness. After sub-beta heat treatments, the LPBF-induced substructures of LAGBs and HAGBs were gradually eliminated, resulting in a decrease in UTS but an increase in elongation. An increase of similar to 57 degrees boundaries was found in the HT700 and HT800 samples, suggesting a boundary transformation during the recrystallization. The transformation is beneficial to the mechanical property. It contributed to a small drop of UTS (similar to 20 MPa) for the HT700 and HT800 samples and significantly improved ductility compared with the as-built samples. The HT900 sample underwent complete recrystallization with an alpha-lath dominated structure. Thereby it exhibits a better ductility but a lower UTS compared with the HT700 and HT800 samples. After the super-beta heat treatments, a large amount of martensite reappeared. Due to the large size of prior 1 grains, the ductility was significantly decreased. The results of this study can be used to guide the adjustment of the microstructure of LPBF-processed Ti-6.5Al-2Zr-Mo-V alloy through post-heat treatments to obtain a good combination of tensile properties.

Microstructure and Mechanical Properties of Ti-6.5Al-2Zr-Mo-V Alloy Processed by Laser Powder Bed Fusion and Subsequent Heat Treatments

Tailoring the microstructure and mechanical property of laser powder bed fusion fabricated Ti–6Al–2Sn–4Zr–2Mo via heat treatment

Influence of Powder Bed Temperature on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy Fabricated via Laser Powder Bed Fusion

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Additive Manufactured Ti-6.5Al-2Zr-1Mo-1V Alloy

Process-structure-property Modeling for Postbuild Heat Treatment of Powder Bed Fusion Ti-6Al-4V

Heat-treatment induced microstructural evolution and enhanced mechanical property of selective laser melted near β Ti-5Al-5Mo-5 V-3Cr-1Zr alloy

Influence of post-heat treatments on microstructural and mechanical properties of LPBF-processed Ti6Al4V alloy

Effects of Heat Treatments on Microstructures and Mechanical Properties of Ti6Al4V Alloy Produced by Laser Solid Forming

Heat treatment effect on the microstructure and elevated temperature tensile property of the Ti6242S alloy fabricated via laser powder bed fusion

Microstructure and mechanical evolution behavior of LPBF (laser powder bed fusion)-fabricated TA15 alloy

The impact of heat treatment on microstructure, residual stress, and mechanical behavior of laser powder bed fusion additively manufactured Ti–6Al–2Sn–4Zr–2Mo alloy

Innovative Fabrication Design for In Situ Martensite Decomposition and Enhanced Mechanical Properties in Laser Powder Bed Fused Ti6Al4V Alloy

Revealing the intensified preferred orientation and factors dominating the anisotropic mechanical properties of laser powder bed fusion Ti‐6Al‐4V alloy after heat treatment

Effect of Subtransus Heat Treatment on the Microstructure and Mechanical Properties of Additively Manufactured Ti-6Al-4V Alloy

Exploring the Heat Treatment Parameters, Microstructural Evolution, and Mechanical Properties of Ti–6Al–4V Alloy Fabricated by a Selective Laser Melting Process

Effect of processing parameters on the defects, microstructure, and property evaluation of Ti-6Al-4V titanium alloy processed by laser powder bed fusion

Mechanical behavior and microstructure evolution of Al-Cu-Mg alloy produced by laser powder bed fusion: Effect of heat treatment

Effect of heating treatment on the microstructural evolution and dynamic tensile properties of Ti-6Al-4V alloy produced by selective laser melting

Performance of Ti6Al4V fabricated by electron beam and laser hybrid preheating and selective melting strategy

The Martensitic Transformation and Mechanical Properties of Ti6Al4V Prepared Via Selective Laser Melting

Effect of Ti microalloying and laser remelting on the microstructure and mechanical properties of laser powder bed fusion Al-12Si alloy