Abstract:The large thermal gradient and high cooling rate generated in the fabrication of complex thin-walled components by laser powder bed fusion (LPBF) may cause uncontrolled deformation and reduce dimensional accuracy. The existing preheating-assisted LPBF process is still difficult to fabricate complex thin-walled components to large size (e.g., reach 800 mm) with the required dimensional accuracy and structural properties. To solve this problem, a novel integrated process of LPBF and hot metal gas forming (HMGF) was proposed in this study to fabricate complex thin-walled components. In this process, a preform with a geometrical shape close to the final component is first fabricated by LPBF process, and then this preform is formed into the desired shape by HMGF process. The hot formability of the LPBF AlSi10Mg sheets was investigated to verify the feasibility of this novel forming process. Also, the hot formability was compared with that of gravity cast (GC) AlSi10Mg sheets. The microstructure, phase structure, uniaxial and biaxial hot formability were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), hot uniaxial tensile and hot biaxial gas bulging experiments, respectively. The results indicated that the cellular microstructure of the LPBF AlSi10Mg gradually disappears with the increase in temperature. The LPBF AlSi10Mg sheet exhibits superior mechanical properties to the GC AlSi10Mg sheet due to the mixed strengthening mechanism among strengthening phase precipitation, grain structure and dynamic recrystallization (DRX) degree. For instance, the former demonstrates a total elongation (obtained from hot uniaxial tensile tests) of 81.2% and an ultimate bulging height (obtained from the hot biaxial gas bulging tests) of 12.16 mm; in contrast, the latter's elongation and bulging height are 56.2% and 9.26 mm, respectively. Moreover, the LPBF AlSi10Mg sheet shows more uniform deformation than the GC AlSi10Mg sheet during the bulging tests. The feasibility of forming the LPBF-fabricated preform by HMGF process was confirmed. This lays a foundation for the integrated process of LPBF and HMGF to fabricate complex thin-walled components.

4D Forming Shape Memory Component of Cu–13Al–5Fe Alloy Based on Laser Powder Bed Fusion of Metal Powders

High-temperature Oxidation Behavior of AlCoCrCuFeNi High-Entropy Alloy by Selective Laser Melting

Achieving dual-phase structured Cu-Al-Mn-Si alloy with prominent shape memory properties via laser powder bed fusion

Fabrication of Integrated Ni-Ti Alloys Possessing Both Super-elastic and Shape Memory Properties by Laser Powder Bed Fusion

Simultaneous enhancement of mechanical and functional properties by heat-treatment in CuAlNi shape memory alloys fabricated by laser powder bed fusion

Fe-Mn-Al-Ni Shape Memory Alloy Additively Manufactured via Laser Powder Bed Fusion

Additive manufacturing of Cu-Al-Mn shape memory alloy with enhanced superelasticity

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Composition design method of Al-Cu alloy for laser powder bed fusion

Effect of Cooling Rate on Microstructure, Shape Memory Effect and Mechanical Properties of Cu–13Al–5Fe High-Temperature Shape Memory Alloy Fabricated by Laser Powder Bed Fusion

Laser-Directed Energy Deposition of Fe-Mn-Si-Based Shape Memory Alloy: Microstructure, Mechanical Properties, and Shape Memory Properties

Formability and microstructure of laser powder bed fused AlSi10Mg alloy sheets under various deformation conditions

Developing a novel lightweight Al–Mg–Li alloy for laser powder bed fusion additive manufacturing: Parameter optimization, microstructure evolution, and mechanical performance

Applicability of LPBF for producing Cu-11Al-5Ni-4Fe wt.% with shape memory properties

Laser Powder Bed Fusion of Sinusoidal Lattice Structure Using Shape Memory Alloys

Effect of Powder Spreading Parameters on Laser Absorption Behavior and Processability of High‐Strength Aluminum Alloy Fabricated by Laser Powder Bed Fusion

Mechanical behavior and microstructure evolution of Al-Cu-Mg alloy produced by laser powder bed fusion: Effect of heat treatment

Developing ductile and isotropic Ti alloy with tailored composition for laser powder bed fusion

High strength Al–Li alloy development for laser powder bed fusion

Laser Powder Bed Fusion of NiTiHf High-Temperature Shape Memory Alloy: Effect of Process Parameters on the Thermomechanical Behavior

Effects of the microstructure and texture characteristics on mechanical properties of the Al–Ni–Cu–Fe alloy manufactured by laser powder bed fusion