Abstract:Additive manufacturing (AM) introduces unique grain feature and anisotropy in metals, as well as relatively poor surface quality, so the knowledge about the formation of post-machining-induced surface integrity needs to be extended. This study aims to understand the machining phenomena in orthogonal cutting of Inconel 718 produced via powder bed fusion of metals using a laser beam system (PBF-LB/M), paying particular attention to the cutting energy, chip formation, geometrical defects, and microstructural deformation. Experiments are conducted on both wrought (W 718) and PBF-LB/M (PBF 718) Inconel 718, whereby the cutting speed and the anisotropy of the workpiece in the raw state play an important role. The results indicate that less cutting energy is consumed when cutting PBF 718 in the direction perpendicular to its build direction (BD), followed by cutting in its BD. Denser shearing-induced slip lines and relatively continuous chip morphology are found when cutting PBF 718 in its BD, moreover, the effect of cutting speed on shearing deformation of columnar grains under this condition is analysed. More importantly, this study identifies a significant geometrical defect phenomenon which is unique to PBF 718 and highly depends on the cutting speed and anisotropy of grain feature. A detailed characterisation shows that this behaviour is caused by tearing within the grains in the matrix material and not by the presence of hard inclusions, which has rarely been reported in the literature. The microstructure in the subsurface area exhibits that the density of grain boundaries in the cutting direction plays the key role in plastic deformation, as the machining process mainly causes dragging behaviour in the area below the machined surface. Thus, cutting PBF 718 in the direction perpendicular to its BD shows similar deformation layer to W 718, while cutting PBF 718 in its BD displays much stronger subsurface deformation. The obtained results greatly help to understand the cutting phenomena in post-machining of additively manufactured Ni-based components, especially the integrity for a better functional surface.

Surface Modification and Mechanical Properties of Laser Powder Bed Fusion Inconel 718 after Magnetic-Assisted Laser Polishing

Effects of Magnetic Abrasive Finishing on Microstructure and Mechanical Properties of Inconel 718 Processed by Laser Powder Bed Fusion

Improving surface quality and superficial microstructure of LDED Inconel 718 superalloy processed by hybrid laser polishing

Machinability Evaluation and Surface Characteristics in Post-machining of Inconel 625 Fabricated by Laser Powder-Bed Fusion

Modification of surface characteristics and electrochemical corrosion behavior of laser powder bed fused stainless-steel 316L after laser polishing

Optimisation of the laser polishing for laser-powder bed fusion and electron beam-powder bed fusion Ti6Al4V surfaces

Study of selective laser melting (SLM) Inconel 718 part surface improvement by electrochemical polishing

Experimental Investigation on the Effect of Surface Shape and Orientation in Magnetic Field Assisted Mass Polishing

Tribological Behaviors of LDED Inconel 718 Samples Polished with a Hybrid Laser Polishing Technique

Effects of laser polishing on surface morphology and mechanical properties of additive manufactured TiAl components

Effect of electropulsing-assisted ultrasonic nanocrystal surface modification on microstructures and hardness of additive manufactured Inconel 718

Formability, Microstructure and Properties of Inconel 718 Superalloy Fabricated by Selective Laser Melting Additive Manufacture Technology

Promoting the densification and grain refinement with assistance of static magnetic field in laser powder bed fusion

Improving Surface Electrochemical Polishing Quality of Additive Manufactured AlSi10Mg by Reconstituting the Si Phase

Post-processing effects on the surface characteristics of Inconel 718 alloy fabricated by selective laser melting additive manufacturing

Influence of In Situ Laser Polishing on Pore Defects and Mechanical Properties of IN718 Alloy Fabricated by Selective Laser Melting

Tailoring Microstructure and Mechanical Properties of Additively Manufactured Inconel 625 by Remelting Strategy in Laser Powder Bed Fusion

Effect of Initial Surface Morphology and Laser Parameters on the Laser Polishing of Stainless Steel Manufactured by Laser Powder Bed Fusion

Enhancing high-temperature performance of Inconel 718 LDED samples through hybrid laser polishing post-treatment

On machining-induced surface integrity of Inconel 718 fabricated by powder bed fusion

In-Situ Laser Polishing Additive Manufactured AlSi10Mg: Effect of Laser Polishing Strategy on Surface Morphology, Roughness and Microhardness