Abstract:Laser-assisted electrochemical machining (ECM) is an ideal manufacturing method for Inconel 718 (IN718) because of the method's high efficiency and good surface quality, and the basis for and key to laser-assisted ECM is its anodic electrochemical dissolution behavior. In this study, IN718 in a 10 wt % NaNO3 solution was subjected to innovative electrochemical testing and laser-assisted ECM experiments to investigate its corrosion properties and the passive film characteristics formed on its surface. The passivation-related behaviors and structures of the passive film were investigated based on open-circuit potentials, dynamic polarization, potentiostatic polarization, and electrochemical impedance spectroscopy. It was found that there was obvious active-passive-transpassive transition behavior, and the structure of the passive film in laser-assisted ECM exhibited pores and defects, resulting in weak corrosion resistance, compared with IN718 under ECM without laser irradiation. The chemical composition of the passive film was obtained by X-ray photoelectron spectroscopy. The results showed that the passive film was composed mainly of a mixture of NiO, Ni(OH)2, Cr2O3, CrO3, Fe2O3, α-Fe2O3, α-FeOOH, Nb2O5, NbO, MoO3, MoO2, and TiO2. The passive film formed by laser-assisted ECM was rich in NiO and TiO2 and lacked Cr2O3 and MoO3, which validated its pores and defect structures. A corresponding schematic model was also proposed to characterize the interface structure between the IN718 substrate and the passive film. Laser-assisted ECM tests were performed under different current densities and machining times, and the corrosion morphology of IN718 was identified. Corrosion pits and a loose product layer appeared on the machined surface at low current densities, and the dissolution mechanism was pitting. The quantity and depth of the corrosion pits dispersed on the machined surface clearly decreased as the current density increased. Finally, a quantitative corrosion model was established to characterize the dissolution behavior of IN718 in NaNO3 solution during laser-assisted ECM.

Study of selective laser melting (SLM) Inconel 718 part surface improvement by electrochemical polishing

Electrochemical polishing of selective laser melted Inconel 718

Improving surface quality and superficial microstructure of LDED Inconel 718 superalloy processed by hybrid laser polishing

Influence of In Situ Laser Polishing on Pore Defects and Mechanical Properties of IN718 Alloy Fabricated by Selective Laser Melting

Dry mechanical-electrochemical polishing of selective laser melted 316L stainless steel

Tribological Behaviors of LDED Inconel 718 Samples Polished with a Hybrid Laser Polishing Technique

Study on Grindability of Inconel 718 Superalloy Fabricated by Selective Laser Melting (SLM)

Enhancing high-temperature performance of Inconel 718 LDED samples through hybrid laser polishing post-treatment

Mechanical properties and microstructure evolution of selective laser melting Inconel 718 along building direction and sectional dimension

Effect of electropulsing-assisted ultrasonic nanocrystal surface modification on microstructures and hardness of additive manufactured Inconel 718

Improving Surface Electrochemical Polishing Quality of Additive Manufactured AlSi10Mg by Reconstituting the Si Phase

Comparative Investigation on Grindability of Inconel 718 Made by Selective Laser Melting (SLM) and Casting

Microstructure and Electrochemical Corrosion Behavior of Inconel 718 Alloy Fabricated by Selective Laser Melting

Exploring the post-heat treatment on the electropolishing characteristics of laser powder bed fusion processed Inconel 718 superalloy

Corrosion Properties and Passive Film Interface of Inconel 718 in NaNO3 Solution for Laser-Assisted Electrochemical Machining

A comparison study of the electrochemical polishing of laser powder bed fusion HR-2 stainless steel and AlSi10Mg

Effects of laser scanning speed and building direction on the microstructure and mechanical properties of selective laser melted Inconel 718 superalloy

Combined Thermo-Mechanical Techniques for Post-processing of the SLM-Printed Ni-Cr-Fe Alloy Parts

Improvement on surface quality of 316L stainless steel fabricated by laser powder bed fusion via electrochemical polishing in NaNO3 solution

Electrochemical polishing with glycol-based electrolyte of the curved internal channels fabricated via laser powder bed fusion

Formability, Microstructure and Properties of Inconel 718 Superalloy Fabricated by Selective Laser Melting Additive Manufacture Technology