Abstract:IN738 superalloy with excellent high-temperature performance is of huge interest for hot-end component applications in aerospace, but its additive manufacturing via selective laser melting (SLM) is rather challenging due to the unsolved high crack susceptibility. Here, for the purpose of improving the formability of IN738 in SLM, Mn + Si content was then strictly controlled in raw powder. An orthogonal experiment was then carried out under different energy inputs to investigate the characteristics of the molten pool, metallurgical defects, microstructures, and mechanical properties of IN738 by SLM. The results showed that high laser power was more likely to shape large melting depth and depth-to-width ratio under the same linear energy density (LED), rather than scanning speed. Four morphologies of the molten pool were observed in the entire LED range. At lower LEDs, hot cracks were usually accompanied by irregular pores due to the stress concentration at the sharp corner of pores; at higher LEDs, cracks were located at the interface of grain boundaries with large misorientation angles. Energy dispersive spectrometry results revealed that the presence of Al-rich oxides and high Mn + Si content at the interface were the main reasons for cracking. The Scheil-Gulliver solidification modeling was used to examine the cracking susceptibility of Si and Mn elements. In addition, both dendrites and cellular dendrites were found in columnar grain structures. By reducing the Mn + Si content and optimizing process, crack-free and nearly fully dense samples of IN738 were obtained by SLM with excellent mechanical properties (ultimate tensile strengths = 1206 MPa, yield strength = 866 MPa and elongation = 16.5%), which were much higher than the mechanical properties of conventionally manufactured IN738.

Influence of In Situ Laser Polishing on Pore Defects and Mechanical Properties of IN718 Alloy Fabricated by Selective Laser Melting

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Effect of Layer-Wise Varying Parameters on the Microstructure and Soundness of Selective Laser Melted INCONEL 718 Alloy

Improving surface quality and superficial microstructure of LDED Inconel 718 superalloy processed by hybrid laser polishing

Influence of Process Parameters on the Interlaminar Shear Strength of CF/PEEK Composites In-Situ Consolidated by Laser-Assisted Automated Fiber Placement

Effect of Laser Power and Scanning Speed on the Microstructure and Mechanical Properties of SLM Fabricated Inconel 718 Specimens

Study of selective laser melting (SLM) Inconel 718 part surface improvement by electrochemical polishing

Formability, Microstructure and Properties of Inconel 718 Superalloy Fabricated by Selective Laser Melting Additive Manufacture Technology

Influence of Selective Laser Melting Additive Manufacturing Parameters in Inconel 718 Superalloy

Effects of Sandblasting and HIP on Very High Cycle Fatigue Performance of SLM-fabricated IN718 Superalloy

Effect of Laser Energy Density on the Microstructure, Mechanical Properties, and Deformation of Inconel 718 Samples Fabricated by Selective Laser Melting

Analysis of Microstructure and Mechanical Properties in As-Built/As-Cast and Heat-Treated Conditions for IN718 Alloy Obtained by Selective Laser Melting and Investment Casting Processes

Material Characterization and Lubricating Behaviors of Porous Stainless Steel Fabricated by Selective Laser Melting

Influence of pulsed laser scanning patterns on microstructural evolution and mechanical properties of Inconel 718 in direct laser deposition

Laser Polishing of Additive Manufactured 316L Stainless Steel Synthesized by Selective Laser Melting

Influence of Scanning Strategy and Post-Treatment on Cracks and Mechanical Properties of Selective-Laser-Melted K438 Superalloy

Selective laser melting of IN738 superalloy with a low Mn+Si content: Effect of energy input on characteristics of molten pool, metallurgical defects, microstructures and mechanical properties

Microstructure and mechanical performance of ODS superalloys manufactured by selective laser melting

Effect of Laser Energy Density on the Microstructure and Microhardness of Inconel 718 Alloy Fabricated by Selective Laser Melting

Microstructure and mechanical property comparison of Inconel alloys fabricated using micro and conventional laser powder bed fusion

Microstructural evolution and mechanical properties of Alloy 718 fabricated by selective laser melting following different post-treatments