Abstract:The multiphase microstructure evolution and mechanical properties of an ultra-low carbon medium manganese quenching-partitioning-tempering (QPT) steel have been investigated based on the nanoscale austenite reversion correlated with the co-precipitation behavior. The blocky austenite (aspect ratio < 3) was found to nucleate in the partitioning process, and growth occurred in the tempering stage, but the film austenite (aspect ratio > 3) always formed during the tempering procedure in the alloy-enriched structures after partitioning. The adjacent co-precipitation of Ni-rich particles shells with Cu-rich precipitates was observed in quenching-tempering (QT) steels. The lower annealing temperature of QPT-1 steels resulted in a multiphase constitution of mostly film austenite, nanoscale dispersed Ni-rich precipitates and in the obvious coarsening and anisotropic growth of Cu-rich precipitates. With a high annealing temperature, QPT-2 steels showed a large percentage of blocky austenite, an entire core-shell co-precipitation structure of Ni-rich and Cu-rich precipitates in martensite and elongated Cu-rich particles in the blocky austenite. The introduction of nanoparticles in dual phase has rarely been found in ultra-low carbon steels with a low alloying degree. The co-precipitation mechanisms are closely related to the cooperative austenite reversion process, which is governed by Mn diffusion and segregation: this leads to a different element enrichment degree in dual phase. In addition, the intergranular precipitates in QT-steels result in stress concentration in the grain boundaries and a very low ductility, although with strong modulus and Orowan hardening effects. The difference of yield strength (67 MPa) in the two QPT steels mainly originate from the contribution of dispersion strengthening effect (44 MPa) under the consideration of the constituent phases. The lower mechanical stability of the blocky austenite in QPT-2 steels results in a lower uniform elongation and impact toughness.

Structure and Morphology of M-A Constituent in the CGHAZ of a Quenched and Tempered Ultra-Low-carbon Steel

Structure Character of M-A Constituent in CGHAZ of New Ultra-Low Carbon Bainitic Steel under Laser Welding Conditions

Apparent Morphology and Structure of Martensite in Ultrahigh Carbon Steel

Martensite Transformation of an Ultra-High Carbon Steel and Grain Size Effect on Sub-Structure

Grain Refinement Mechanism in the CGHAZ of Ultra-High-Strength Structural Steel: A Critical Analysis of the Impacts of Prior Austenite Grain and Cooling Rates

Mechanism of Interfacial Microstructure Evolution of G115 Steel in Simulated Heat Affected Zone

Evolution of M-A Constituents in HAZ and Its Effect on Toughness of MAG Joint of Granular Bainitic Steel Q690C

Effect of undercooled austenite ausforming on the role of the M–A constituents in the CGHAZ toughness of the HSLA steels with bainite structure

Favorable Impact Toughness of High Heat Input Coarse-Grained HAZ in an Ultra-Low Carbon High-Strength Microalloyed Steel

Effect of Martensitic Morphology on Mechanical Properties of an As-Quenched and Tempered 25crmo48v Steel

Kinetics of Martensite/Austenite Decomposition during Tempering of Ultrafine Nano-Bainitic Steels

Characteristic of martensite–austenite constituents in coarse grained heat affected zone of HSLA steel with varying Al contents

Microstructure Transformation on Pre-Quenched and Ultrafast-Tempered High-Strength Multiphase Steels

Effect of Initial Microstructure on the Toughness of Coarse-Grained Heat-Affected Zone in a Microalloyed Steel

Crystallography of Transformation Products with Different Cooling Rates in Low-Carbon Alloy Steel and Its Effect on Low-Temperature Toughness Uniformity of Heavy Plates

Microstructure and Toughness of the CGHAZ of an Offshore Platform Steel

The Austenite Reversion and Co-Precipitation Behavior of an Ultra-Low Carbon Medium Manganese Quenching-Partitioning-tempering Steel

Significant influence of heat input on microstructure evolution and mechanical properties of the simulated CGHAZ in a 1000 MPa grade ultra-high strength steel

On the role of Cu addition in toughness improvement of coarse grained heat affected zone in a low carbon high strength steel

Effect of Microstructure on Impact Toughness and Fatigue Performance in Coarse-Grained Heat-Affected Zone of Bainitic Steel Welds

Fracture Mode of Martensite-Austenite Constituents Containing Multiphase Steel Controlled by Microstructural and Micromechanical Aspects