Abstract:The effects of trace transition elements (Mn, Cr, V) on the solidification microstructure and the thermal conductivity of Al-9Si based alloys have been investigated. It was found that the effect of Mn, Cr, V on the solidification behavior and solidification microstructure is mainly related to α-Al grains via affecting heterogeneous nucleation and growth restriction, while no significant effect on the solidification behavior and microstructure of eutectic Si was observed. Compared with factors including grain size of α-Al and morphology characteristics (e.g. size, spacing, and shape factor) of eutectic Si, the solid solubility in Al matrix is confirmed to be one of the most important factors affecting thermal conductivity. Due to the larger partition coefficient of V compared with Cr and Mn, the solid solubility and the lattice distortion of α-Al in Al-9Si-xV alloy were increased significantly, thus the thermal conductivity of alloy was decreased steeply from 171.7 to 152.3 W/m·K with the content of V increasing from 15 to 1010 ppm. A linearly fitted curve reflecting the relationship between the content of the transition elements and the thermal conductivity of alloys has been proposed, which can be used to optimize the alloy composition in subsequent remelting or recycling process. Furthermore, two thermal conductivity models (H-S model and Maxwell model) also have been used to evaluate the effect of Mn, Cr, V on thermal conductivity, in which the thermal conductivity of α-Al was corrected based on the measured solid solubility. In this way, the data correlation between the experimental and fitted value based on H-S model and Maxwell model is increased from 0.18 to 0.96. These obtained results could be helpful to precisely control the composition and further improve the thermal conductivity of Al-Si based alloy during the primary production and / or recycling process.

Effect of Alloying Elements on Thermal Conductivity of Aluminum

Thermal Conductivity of Aluminum Alloys—A Review

Elucidating thermal conductivity mechanism of Al-9Si based alloys with trace transition elements (Mn, Cr, V)

Effect of Alloying Elements and Processing Parameters on Microstructure and Properties of 1XXX Aluminium Alloys

Influence of Si, Cu, B, and Trace Alloying Elements on the Conductivity of the Al-Si-Cu Alloy

Effects of Alloying Elements and Temperature on Thermal Conductivity of Ferrite

Effects of Si and Sr elements on solidification microstructure and thermal conductivity of Al–Si-based alloys

A Quantitative Study on the Interaction Between Silicon Content and Heat Treatment on Thermal Conductivity of Al-Si Binary Alloys

Design and preparation of aluminum alloy with high thermal conductivity based on CALPHAD and first-principles calculation

The Influence of Substitutional Defects of Transition Metal Elements on the Stability and Thermal Properties of Al at Finite Temperatures: A First-Principles Study

Quantitative Study of Microstructure-Dependent Thermal Conductivity in Mg-4Ce-xAl-0.5Mn Alloys

Thermal and electrical conductivity of binary magnesium alloys

Effect of microalloying additions on microstructural evolution and thermal stability in cast Al-Ni alloys

Alloying Elements Effects on Electrical Conductivity and Mechanical Properties of Newly Fabricated Al Based Alloys Produced by Conventional Casting Process

Influence of Alloying Elements on Phase Stability and Elastic Properties of Aluminum and Magnesium Studied by First Principles

Effect of Silicon Micro-Alloying on the Thermal Conductivity, Mechanical Properties and Rheological Properties of the Al–5Ni Cast Alloy

Sustainable choices of alloying element for aluminium for thermal conductivity in circular manufacturing

The effect of alloying element on the thermophysical properties of carbon fiber-graphite flakes/copper composites

Effect of Alloying Elements on the Short-Range Orders and Atomic Diffusion Behavior of Liquid Al−9Si Cast Alloys

Thermal Characteristics of Mg–Zn–Mn Alloys with High Specific Strength and High Thermal Conductivity

Internal friction and heat resistance of Al, Al–Ce, Al–Ce–Zr and Al–Ce–(Sc)–(Y) aluminum alloys with high strength and high electrical conductivity