Abstract:Cu matrix composites have received increased attention in a wide industrial area because of their excellent mechanical properties and good electrical and thermal conductivity. However, the addition of general ceramic reinforcements often leads to a marked reduction in electrical conductivity for Cu matrix composites. In this study, the ZrB 2 -reinforced Cu composites have been developed to overcome this drawback since these metal borides possess relatively high electrical conductivity. The 5 wt.% ZrB 2 /Cu composites were prepared using hot-pressed sintering techniques at varying temperatures from 760 to 920°C. The influence of sintering temperature on the microstructure, relative density, and mechanical and electrical properties was examined. The results of the SEM observation show that ZrB 2 particles are seamlessly integrated into the Cu matrix for all ZrB 2 /Cu composites. The average grain size of the Cu matrix increases from 360 to 980 nm with the increase of the sintering temperature. The increase in sintering temperature also leads to the surface porosity decrease from 1.4 to 0.4%. The relative density and electric conductivity of the composites increase at the same time as the sintering temperature increases. However, microhardness increases and decreases, with a maximum value of 92 HV0.2 achieved at 840°C. The elastic modulus and nanohardness maps determined from the nanoindentation indicate that the reinforced ZrB 2 particles demonstrate the highest values for elastic modulus (340–500 GPa) and nanohardness (30–48 GPa). At the same time, the Cu matrix possesses a modulus of 100–200 GPa and nanohardness of about 10 GPa. TEM observation confirmed that the sintering temperature exhibits little influence on the interface reaction between ZrB 2 and Cu. Both sharp interface and interface with amorphous transition layer are observed. The variation of microhardness is mainly due to the strengthening of grain refinement and to the mismatch of the thermal expansion coefficients. The above results can provide further insights into the deeper understanding of the role of sintering temperature during hot-pressed sintering.

The effect of alloying element on the thermophysical properties of carbon fiber-graphite flakes/copper composites

Effects of Zr-Cu Alloy Powder on Microstructure and Properties of Cu Matrix Composite with Highly-Aligned Flake Graphite

Improvement in the thermal conductivities and bending strengths of graphite film/Cu composites by matrix alloying with Zr

Effect of alloying element Zr on microstructure and properties of Cu−Y2O3 composites

Effect of Interfacial Microstructure on the Thermal-Mechanical Properties of Mesophase Pitch-Based Carbon Fiber Reinforced Aluminum Composites

Effect of Cu and Zn elements on morphology of ceramic particles and interfacial bonding in TiB2/Al composites

Effects of alloy elements (Mg, Zn) on the microstructure and mechanical properties of (TiC+TiB2)/Al composites

Effect of Graphite Flakes Particle Sizes on the Microstructure and Properties of Graphite Flakes/copper Composites

Investigation of the Microstructure and Mechanical Properties of Copper-Graphite Composites Reinforced with Single-Crystal α-Al2O3 Fibres by Hot Isostatic Pressing

Effect of Ti–Cu alloy's composition on microstructure and performance of carbon fiber reinforced TiC-based composites prepared by alloyed reactive melt infiltration

Thermophysical properties of Cu-coated carbon fibers reinforced aluminum matrix composites by stir casting

Effect of TM (tm=fe, Mn, Cr) Alloying on the High Temperature Properties and Strengthening Mechanism of Cf/Al Composites

The Roles of Geometry and Topology Structures of Graphite Fillers on Thermal Conductivity of the Graphite/aluminum Composites

Synergistic enhancing effect of tungsten-copper coated graphite flakes and aluminum nitride nanoparticles on microstructure, mechanical and thermal properties of copper matrix composites

The Effect of Aluminum Content on Tio2 Coated Carbon Fiber Reinforced Magnesium Alloy Composites

Effect of Cu Content on Microstructure and Properties of Al2o3-Sio2 Fiber Reinforced Aluminum Matrix Composites

Effect of copper coating on interfacial properties, interfacial thermal resistance, microstructure evolution and mechanical properties of aluminum matrix composites

Effects of Alloy Elements on Ductility and Thermal Conductivity of Compacted Graphite Iron

Enhanced mechanical and tribological properties of copper matrix composites reinforced by copper-coated graphite and Ti3AlC2

Effect of Sintering Temperature on the Microstructure and Properties of High-Strength and Highly Conductive 5 wt.% ZrB2/Cu Composite

Effect of carbon nanotubes on microstructure and mechanical properties of TiZrVMnCu–Er high entropy alloy composites