Abstract:ZrB2-based 2-based ceramics typically necessitate high temperature and pressure for sintering, whereas ZrB2-SiC 2-SiC ceramics can be fabricated at 1500 degrees C using the process of reactive melt infiltration with Si. In comparison to the conventional preparation method, reactive synthesis allows for the more facile production of ultra-high temperature ceramics with fine particle size and homogeneous composition. In this work, ZrSi2, 2 , B4C, 4 C, and C were used as raw materials to prepare ZrB2-SiC 2-SiC via combination of tape casting and reactive melt infiltration herein referred to as ZBC ceramics. Control sample of ZrB2-SiC 2-SiC was also prepared using ZrB2 2 and SiC as raw materials through an identical process designated as ZS ceramics. Microscopic analysis of both ceramic groups revealed smaller and more uniformly distributed particles of the ZrB2 2 phase in ZBC ceramics compared to the larger particles in ZS ceramics. Both sets of ceramics underwent cyclic oxidation testing in the air at 1600 degrees C for a cumulative duration of 5 cycles, each cycle lasting 2 h. Analysis of the oxidation behavior showed that both ZBC ceramics and ZS ceramics developed a glassy SiO2-ZrO2 2-ZrO 2 oxide layer on their surfaces during the oxidation. This layer severed as a barrier against oxygen. In ZBC ceramics, ZrO2 2 is finely distributed in SiO2, 2 , whereas in ZS ceramics, larger ZrO2 2 particles coexist with glassy SiO2. 2 . The surface oxide layer of ZBC ceramics maintains a dense structure because the well-dispersed ZrO2 2 increases the viscosity of glassy SiO2, 2 , preventing its crystallization during the cooling. Conversely, some SiO2 2 in the oxide layer of ZS ceramics may crystallize and form a eutectic with ZrO2, 2 , leading to the formation of ZrSiO4. 4 . This leads to cracking of the oxide layer due to differences in thermal expansion coefficients, weakening its barrier effect. An analysis of the oxidation resistance shows that ZBC ceramics exhibit less increase in oxide layer thickness and mass compared to ZS ceramics, suggesting superior oxidation resistance of ZBC ceramics.

Oxidation Behaviors of ZrB2–SiC Ceramics with Different Porosity

Preparation and Properties of ZrB2-SiC Porous Ceramics by Spark Plasma Sintering

Effect of atomic oxygen on oxidation behavior of ZrB2-SiC ceramic composite materials

Effects of porosity and pore size on mechanical and thermal properties as well as thermal shock fracture resistance of porous ZrB2–SiC ceramics

High Temperature Oxidation Behavior of ZrB2-SiC Added MoSi2 Ceramics

Oxidation Resistance Behavior of Short Carbon Fiber Reinforced ZrB2,-SiC Composites

Oxidation Behavior of ZrB2–SiC–ZrO2 Ceramic Composites in the Temperature Range of 800–1200°C

Oxidation Kinetics of Hot-Pressed ZrB2–SiC Ceramic Matrix Composites

Oxidation Behaviors of the Pressureless Sintered ZrB<SUB>2</SUB>-SiC Composites: Oxidation Behaviors of the Pressureless Sintered ZrB<SUB>2</SUB>-SiC Composites

Microstructure and Oxidation Behavior of ZrB2-SiC 2-Sic Ceramics Fabricated by Tape Casting and Reactive Melt Infiltration

Oxidation Behaviour of Plasma-Sprayed ZrB2-SiC Coatings

High‐Temperature Oxidation at 1900°C of ZrB2–xSiC Ultrahigh‐Temperature Ceramic Composites

Effect of Zr2Al4C5 Content on the Mechanical Properties and Oxidation Behavior of ZrB2-SiC-Zr2Al4C5 Ceramics

Effect of surface microstructure on the temperature response of ZrB 2 –SiC composites

Oxidation Resistance Performance of ZrB_2-SiC Ceramic Matrix Composites

Oxidation behavior of zirconium diboride–silicon carbide at 1800°C

Effect of Surface Oxidation on Thermal Shock Resistance of ZrB 2 –sic–zrc Ceramic at Temperature Difference from 800 to 1900 °C

Effect of Surface Oxidation on Thermal Shock Resistance of the ZrB2–SiC–ZrC Ceramic

OXIDATION OF ZIRCONIUM DIBORIDE-SILICON CARBIDE CERAMIC COMPOSITES IN DISSOCIATED OXYGEN

Oxidation Behaviour of ZrB2–SiC (al/y) Ceramics at 1700 °C

The oxidation behaviors of a ZrB2-SiC-ZrC ceramic