Abstract:Unraveling the varied modification mechanisms of trace elements under diverse cooling rates is of great importance to regulate the morphology of primary Mg 2 Si in hypereutectic Al-Mg 2 Si alloys. In the present work, the modification mechanisms of Sr and Sb in Al-20Mg 2 Si alloys under different cooling rates are discussed in detail. Increasing the cooling rates from ~ 50 to 76 °C/s to ~ 213 to 230 °C/s leads to the morphology transition of primary Mg 2 Si from hoppers to dendrites, which is attributed to a smaller constitutional zone with the increase of temperature gradients introduced by high cooling rates. The addition of 0.15 wt pct Sr modifies the morphology of primary Mg 2 Si phase to cubes at cooling rates of ~ 50 to 76 °C/s and ~ 213 to 230 °C/s with the same modification mechanism, i.e. , by increasing nucleation driving force for primary Mg 2 Si and the adsorption-poisoning effect. In contrast, the modification mechanisms of Sb are different under varying cooling rates. At low cooling rates of ~ 50 to 76 °C/s, Sb modifies the morphology of primary Mg 2 Si to be truncated octahedrons by introducing Mg 3 Sb 2 particles as heterogeneous nuclei and the substitution of Sb to Si in Mg 2 Si crystals. At high cooling rates of ~ 213 to 230 °C/s, primary Mg 2 Si grows coarser with a dendrite morphology due to solute trapping, which changes the modification mechanism to substitution alone. Moreover, it is interesting that at cooling rates of ~ 213 to 230 °C/s, primary and eutectic Mg 2 Si particles in the Al-20Mg 2 Si-0.15Sr alloy are refined simultaneously, which greatly suppresses the crack formation and propagation. Accordingly, the ultimate tensile strength and elongation to failure are increased to ~ 242 MPa and ~ 5.6 pct compared to the unmodified alloy (~ 188 MPa and ~ 1.4 pct, respectively).

The Growth Mechanism and Morphology Evolution of Primary Si During Slow Cooling Solidification of High Purity Al–15Si Alloy with Cr Additions

Effects of Cr Addition on the Microstructure and Mechanical Properties of an Al-Si-Cu-Mg Alloy

Growth Mechanism of Eutectic Si in Super-Gravity Solidified Al-Si Alloy During Annealing

Effects of B Addition on the Microstructure and Properties of Nb Silicide Based Ultrahigh Temperature Alloys

INFLUENCE OF ADDITIVE Sr OR Sb ON MODIFICATION OF Al-Si ALLOYS

Morphology Evolution of Primary Mg2Si in Al–20Mg2Si–0.1Ca Alloys Prepared with Various Solidification Cooling Rates

Effect of Trace Silicon Addition on Microstructure and Properties of a Cu–0.26Cr–0.14Mg Alloy

Effect of Strontium Addition on Silicon Phase and Mechanical Properties of Zn–27Al–3Si Alloy

Formation Mechanism and Effect on the Mechanical Properties of TiSi Phase for Ti-5Al-5Mo-5Cr-3Nb-2Zr Alloyed by Silicon

Effect of Silicon Addition on the Microstructure and Precipitation of Cast Al-5.3Cu-0.8Mg-0.6Ag Alloys

Dendritic Si growth morphologies in highly undercooled Al-Si alloys

Effect of Si Content on the Morphology Evolution of the Si Primary Dendrites in Al-Si Alloy Solvent Refining Process

The effect of Al addition to a Cr solvent without molten Si on the surface morphology in a solution growth of SiC

Evolution of Primary Si Phase, Surface Roughness and Mechanical Properties of Hypereutectic Al–Si Alloys with Different Si Contents and Cooling Rates

Formation mechanism and conditions of fine primary silicon being uniformly distributed on single αAl matrix in Al-Si alloys

Effects of Cr on microstructure and properties of Al-Mg-Si-Cu aluminum alloy

Varied Modification Mechanisms of Sr and Sb under Diverse Cooling Rates on Primary Mg 2 Si in an Al-20Mg 2 Si Alloy

Eutectic Growth in Sr Modified Al–13%Si Alloy under Unidirectional Solidification

Cr-induced Morphology Change of Primary Mn-rich Phase in Al-Si-Cu-Mn Heat Resistant Aluminum Alloys and Its Contribution to High Temperature Strength

Effect of Si addition on the precipitation and mechanical/electrical properties of dilute Al-Zr-Sc alloys

Stoichiometric and Off-Stoichiometric Alloying in Silicide Compound Ti5Si3 by Nb or Cr Additions