Abstract:Unraveling the varied modification mechanisms of trace elements under diverse cooling rates is of great importance to regulate the morphology of primary Mg 2 Si in hypereutectic Al-Mg 2 Si alloys. In the present work, the modification mechanisms of Sr and Sb in Al-20Mg 2 Si alloys under different cooling rates are discussed in detail. Increasing the cooling rates from ~ 50 to 76 °C/s to ~ 213 to 230 °C/s leads to the morphology transition of primary Mg 2 Si from hoppers to dendrites, which is attributed to a smaller constitutional zone with the increase of temperature gradients introduced by high cooling rates. The addition of 0.15 wt pct Sr modifies the morphology of primary Mg 2 Si phase to cubes at cooling rates of ~ 50 to 76 °C/s and ~ 213 to 230 °C/s with the same modification mechanism, i.e. , by increasing nucleation driving force for primary Mg 2 Si and the adsorption-poisoning effect. In contrast, the modification mechanisms of Sb are different under varying cooling rates. At low cooling rates of ~ 50 to 76 °C/s, Sb modifies the morphology of primary Mg 2 Si to be truncated octahedrons by introducing Mg 3 Sb 2 particles as heterogeneous nuclei and the substitution of Sb to Si in Mg 2 Si crystals. At high cooling rates of ~ 213 to 230 °C/s, primary Mg 2 Si grows coarser with a dendrite morphology due to solute trapping, which changes the modification mechanism to substitution alone. Moreover, it is interesting that at cooling rates of ~ 213 to 230 °C/s, primary and eutectic Mg 2 Si particles in the Al-20Mg 2 Si-0.15Sr alloy are refined simultaneously, which greatly suppresses the crack formation and propagation. Accordingly, the ultimate tensile strength and elongation to failure are increased to ~ 242 MPa and ~ 5.6 pct compared to the unmodified alloy (~ 188 MPa and ~ 1.4 pct, respectively).

Evolution of Primary Si Phase, Surface Roughness and Mechanical Properties of Hypereutectic Al–Si Alloys with Different Si Contents and Cooling Rates

Influence of Cooling Rate on Primary Silicon Size in Hypereutectic Al–Si Alloy Fabricated by Laser Powder Bed Fusion

Growth Mechanism of Eutectic Si in Super-Gravity Solidified Al-Si Alloy During Annealing

Microstructure, thermo-physical and mechanical properties of hypereutectic Al-10Ni-xSi alloys

Effect of Cooling Conditions on the Solidification Microstructure and Mechanical Properties of Al–18Si Alloy

Effect of Si on Phase Equilibria, Mechanical Properties and Tribological Behaviour of Al-Cu Alloy

Rapid Eutectic Growth Kinetics of Undercooled Nb-Si Alloys at Electrostatic Levitation State

Morphologies of Primary Silicon in Hypereutectic Al–Si Alloys with Melt Overheating Temperature and Cooling Rate

Varied Modification Mechanisms of Sr and Sb under Diverse Cooling Rates on Primary Mg 2 Si in an Al-20Mg 2 Si Alloy

Varied Modification Mechanisms of Sr and Sb under Diverse Cooling Rates on Primary Mg2Si in an Al-20Mg2Si Alloy

Formation mechanism and conditions of fine primary silicon being uniformly distributed on single αAl matrix in Al-Si alloys

Effect of Cooling Rate on the Microstructure Evolution and Mechanical Properties of Iron-Rich Al–Si Alloy

Hypereutectic Al-Si Binary Alloys Prepared by Melt Spinning Method

Effects of Mg Content on Primary Mg2Si Phase in Hypereutectic Al–Si Alloys

Synergistic Effects of Γ-Al2o3 Nanoparticles and Fast Cooling on the Microstructural Evolution and Mechanical Properties of Al-20Si Alloys

Effect of cooling rates and heat treatment time on Si phase of AlSi10Mg alloy manufactured by selective laser melting: Microstructure evolution and strengthening mechanism

Morphology And Microstructure Of Gas-Atomized Hypereutectic Al-Si Alloy Powders

Microstructure control and performance evolution of hypereutectic Al–20Mg2Si alloy by novel Al–Ca–Sb master alloy

Dissolution kinetics of primary silicon in hypereutectic Al–Si melt

Effect of Si Content on Separation and Purification of the Primary Si Phase from Hypereutectic Al–Si Alloy Using Rotating Magnetic Field

Microstructure Evolution of Spray-Formed Hypereutectic Al-Si Alloys in Semisolid Reheating Process