Abstract:The main objective of this research was to investigate the effect of adding CuO (2 wt.%) nanoparticles and changing the cooling rate on the microstructure and mechanical properties of Al (2 wt.%) Si. The addition of CuO nanoparticles to Al-2wt.%Si (alloy A) resulted in a composite alloy (alloy B). Optical microscopy (OM), scanning electron microscopy (SEM) connected to an energy-dispersive spectrometer (EDS), x-ray diffraction (XRD), and positron annihilation Doppler broadening spectroscopy (PADBS) were used to examine the microstructure of alloys. Moreover, Vickers hardness and tensile tests were used to investigate the mechanical properties of the tested alloys. The G1 samples were cooled in the air to ~ 300 K and quenched G2 samples in cold water at 0 °C. The results showed that increasing the strain rate from 0.004 to 0.02 min −1 or decreasing the temperature from 503 to 423 K could increase the hardening parameters, yield stress ( σ y ), ultimate strength ( σ M ), and Young's modulus ( Y ) of all samples. Moreover, H V decreased as the aging temperature climbed from 423 to 503 K. Adding nano-sized CuO or cooling samples resulted in smaller grains. Furthermore, alloy B exhibited the formation of intermetallic compounds (IMCs) CuAl 2 and Cu 3 Si. The XRD data indicated the formation of phases in both alloys at 423, 463, and 503 K. In addition, the dislocation density, lattice strain, and average crystallite size were calculated. It can be seen from the activation energies and stress exponents that dislocation climbs through core diffusion as a control mechanism for both alloys. A significant positive relationship was observed between the value ( H v ) and PADBS parameters for all examined samples. The investigation showed that nano-sized CuO and a rapid cooling rate increased composite specimen hardness. This finding confirms that aluminum and its alloys play a crucial role in various technical applications.

Effect of Cooling Conditions on the Solidification Microstructure and Mechanical Properties of Al–18Si Alloy

Effect of Cooling Rate on Solidification Parameters and Microstructure of Al-7Si-0.3Mg-0.15Fe Alloy

Effect of Cooling Rate on the Microstructure Evolution and Mechanical Properties of Iron-Rich Al–Si Alloy

Synergistic Effects of Γ-Al2o3 Nanoparticles and Fast Cooling on the Microstructural Evolution and Mechanical Properties of Al-20Si Alloys

Effects of Cooling Rates on the Solidification Process of Al-Si-Mg Alloy

Influence of Cooling Rate on Primary Silicon Size in Hypereutectic Al–Si Alloy Fabricated by Laser Powder Bed Fusion

Effects of Solidification Cooling Rates on Microstructures and Physical Properties of Fe-6.5%Si Alloys

Formation mechanism and conditions of fine primary silicon being uniformly distributed on single αAl matrix in Al-Si alloys

Synergistic Effect of Strontium and Melt Quenching on the Solidification Microstructure of Hypereutectic Al-Si Alloys

Effect of Cooling Rates and rapidly quenched on Al-Si alloy

Effect of melt overheating, cooling and solidification rates on Al–16wt.%Si alloy structure

Effect of cooling rate on microstructure and mechanical properties of Mg-9Gd-4Y-1Zn-1Al alloy

Effect of ultrasonic melt processing and cooling rate on microstructure evolution of Al–Cu–Mn–Mg–Fe–Si alloy

Effect of Cooling Rate on the Microstructure of Semi-Solid Al–25Si–2Fe Alloy During Electromagnetic Stirring

Microstructure Evolution and Mechanical Properties of a Cast and Heat-Treated Al–Li–Cu–Mg Alloy: Effect of Cooling Rate During Casting

A numerical study of irregular eutectic in Al-Si alloys under a large undercooling

Effect of Cooling Rate on Microstructure and Mechanical Properties of Sand-Casted Al–5.0Mg–0.6Mn–0.25Ce Alloy

Microstructural evolution and mechanical property of Al–Mg–Mn alloys with various solidification cooling rates

Effect of Cooling Rate on Microstructure and Mechanical Properties of an Al-5.0Mg-3.0Zn-1.0Cu Cast Alloy

Effect of CuO Nanostructure Addition and Cooling Rate on the Microstructure and Mechanical Characteristics of Hypoeutectic Al-2wt.%Si Alloy

Microstructure of Al-Si Alloys Rapidly Solidified from the Different Temperature Melts