Abstract:LiNixCoyMn1–x–yO2 (x ≥ 0.5) layered oxide materials are generally considered as one of the most prospective candidates for lithium-ion battery (LIBs) cathodes due to their high specific capacity and working voltage. However, surface impurity species substantially degrade the electrochemical performance of LIBs. Herein, surface reconstruction from layered structure to disordered layer and rock-salt coherent region together with a uniform Li2CO3-dominant coating layer is first in situ constructed on the single-crystal LiNi0.5Co0.2Mn0.3O2 (NCM) material by a simple water treatment procedure. The unique surface structure is elucidated by Ar-sputtering-assisted X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (spherical aberration-corrected-scanning transmission electron microscopy (STEM), high-resolution transmission electron microscopy (HRTEM), and TEM). Meanwhile, neutron powder diffraction (NPD) indicates that the antisite defect concentration is mitigated in the treated materials. The modified samples display superior cycle stability with a capacity retention of up to 87.5% at 1C after 300 cycles, a high rate capacity of 151 mAh g–1 at 5C, an elevated temperature (45 °C) cycling property with 80% capacity retention (4.5 V), and improved full-cell performance with 91% after 250 cycles at 1C. Importantly, postmortem examination on the cycled cathodes by time-of-flight secondary-ion mass spectroscopy (TOF-SIMS), XPS, TEM, and X-ray diffractometer (XRD) pattern further demonstrate that these results are mainly attributed to the thin cathode electrolyte interface (CEI) film and low solubility of transition-metal ions. Therefore, this expedition provides an opportunity to construct an effective armor for the interface compatibility and stability of LIBs.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c21973?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c21973</a>.XRD patterns and SEM images of NCM, NCM-350 °C, NCM-400 °C, and NCM-500 °C; HRTEM and STEM image of NCM; TEM images of NCM and NCM-400 °C cathode; EDS elemental mapping of the NCM cathode particle; XPS spectra of C 1s, O 1s, and Ni 2p for NCM and NCM-400 °C with different sputtering times (0, 5, 10, 20, 30, 60, 120, 180, 240 s); XPS spectra of Li 1s for NCM and NCM-400 °C surface; cycling performance of graphite at 0.5C at 25 °C within a voltage range of 0.01–3.0 V in a half cell against lithium anodes. Digital images of lithium harvested from the disassembled cycled cells after 500 cycles at 5C for NCM and NCM-400 °C. STEM-EDX, XPS spectra in an argon atmosphere, and SEM image of cycled NCM and NCM-400 °C (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c21973/suppl_file/am0c21973_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Pre-Deoxidation of Layered Ni-Rich Cathodes to Construct a Stable Interface with Electrolyte for Long Cycling Life

Enhancing high-voltage performances of nickel-based cathode material via aluminum and progressive concentration gradient modification

Realizing Superior Cycling Stability of Ni-Rich Layered Cathode by Combination of Grain Boundary Engineering and Surface Coating

Surface spinel reconstruction to suppress detrimental phase transition for stable LiNi0.8Co0.1Mn0.1O2 cathodes

Enabling stable and high-rate cycling of a Ni-rich layered oxide cathode for lithium-ion batteries by modification with an artificial Li<SUP>+</SUP>-conducting cathode-electrolyte interphase

In-situ Ti4+-doped modification of layer-structured Ni-rich LiNi0.83Co0.11Mn0.06O2 cathode materials for high-energy lithium-ion batteries

Enhancing cyclic and in-air stability of Ni-Rich cathodes through perovskite oxide surface coating

Enhancing the structural stability of Ni-rich layered oxide cathodes with a preformed Zr-concentrated defective nanolayer.

Enhancement on the Cycling Stability of the Layered Ni-Rich Oxide Cathode by In-Situ Fabricating Nano-Thickness Cation-Mixing Layers

Stabilizing reaction interface in Ni-rich layered oxides cathode for high-performance lithium-ion batteries at a high cutoff voltage

Elevating cycle stability of Ni-rich NCM811 cathode via single-crystallization integrating dual-modification strategy for lithium-ion batteries

Improving the cycling and air-storage stability of LiNi<sub>0.8</sub>Co<sub>0.1</sub>Mn<sub>0.1</sub>O<sub>2</sub> through integrated surface/interface/doping engineering

In Situ Induced Surface Reconstruction of Single-Crystal Lithium-Ion Cathode Toward Effective Interface Compatibility

Improving the Cycling Performance of the Layered Ni-Rich Oxide Cathode by Introducing Low-Content Li2mno3

Construction of internal electric field to suppress oxygen evolution of Ni-rich cathode materials at a high cutoff voltage

Both Interface and Bulk Stable LiNi 0.5 Mn 1.5 O 4 Cathodes for High-Energy Li-Ion Batteries

Lanthanum doping and surface Li 3 BO 3 passivating layer enabling 4.8 V nickel-rich layered oxide cathodes toward high energy lithium-ion batteries

Dually-functionalized Ni-rich layered oxides for high-capacity lithium-ion batteries

Improving the Structure and Cycling Stability of Ni-Rich Layered Cathodes by Dual Modification of Yttrium Doping and Surface Coating

Stabilizing Ni‐Rich LiNi 0.92 Co 0.06 Al 0.02 O 2 Cathodes by Boracic Polyanion and Tungsten Cation Co‐Doping for High‐Energy Lithium‐Ion Batteries

Constructing Stable Interface Layer for Boosting High-Voltage Cycling Performance of Single-Crystal Ni-rich Cathodes