Abstract:Digital light processing (DLP) is increasingly widely used to manufacture high-precision complex structural ceramic components quickly and efficiently. However, due to the high absorbance of silicon carbide (SiC) micron fine powder and the high refractive index difference between the powder and the photosensitive resin, it is extremely challenging to DLP print SiC with high precision complex structure. Here, the surface of SiC powder was coated with SiO 2 nano-layer of different thickness by controllable oxidation coating method, thus realizing the photocurable printing of SiC@SiO 2 green bodies with structural precision up to 80 μm. Through the two-step reaction method of carbothermal reduction combined with gas-phase siliconizing (GSI), not only the SiO 2 coated layer was effectively removed, but also the reaction-bonded silicon carbide (RB-SiC) ceramics with 80–300 μm periodic structure was successfully realized. Ultimately, the comprehensive performance of the RB-SiC samples is effectively improved by chemical vapor infiltration of silicon carbide (CVI-SiC). It is noteworthy that the maximum elastic modulus and hardness of the ultima SiC specimens (RB-SiC@CVI-SiC) are as high as 394.599 GPa and 50.241 GPa, respectively. Shockingly, the nanomechanical properties of postgenetic RB-SiC bound to initial α-SiC on the cross-section of ultima specimens were much higher than those of CVI-SiC on the surface. This study fills the gap that liquid-phase siliconizing (LSI) or pyrolysis process could not achieve high-performance SiC ceramics with micron-level periodic structure.

SiC Paste with High Curing Thickness for Stereolithography

Investigation of curing behavior and mechanical properties of SiC ceramics prepared by vat photopolymerization combined with pressureless liquid-phase sintering using Al 2 O 3 -coated SiC powder

Rheological behavior and curing deformation of paste containing 85 wt% Al2O3 ceramic during SLA-3D printing

Properties regulation of SiC ceramics prepared via stereolithography combined with reactive melt infiltration techniques

Formation mechanism of stereolithography of Si3N4 slurry using silane coupling agent as modifier and dispersant

Preparation of photosensitive SiO2/SiC ceramic slurry with high solid content for stereolithography

Preparation of silicon carbide ceramic slurry for stereolithography based additive manufacturing

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

Enhanced Molding and Mechanical Properties of SiC-based Ceramic Lattice Structures Via Digital Light Processing

Controllable reduction of absorbance and two-step reaction for 3D-printed SiC ceramics with micron-level periodic structure

Microstructure Evolution and Performance Improvement of Silicon Carbide Ceramics via Impregnation Method

Optimizing the properties of vat photopolymerization 3D-printed SiC ceramics by multi-infiltration

Effect of TMAH as a modifier on the performance of Si3N4 stereolithography pastes

Preparation of low residual silicon content Si-SiC ceramics by binder jetting additive manufacturing and liquid silicon infiltration

Si 3 N 4 slurry with high solid phase, low viscosity prepared via surface-oxidation and silane coupling agent modification hybrid method

Curing behaviors and mechanical properties of SiC-whisker-reinforced alumina ceramics fabricated with digital light processing

Stereolithography-based additive manufacturing of lightweight and high-strength Cf/SiC ceramics

Densification mechanism of stereolithographical dense Si3N4 ceramics with CeO2 as sintering additive by field assisted sintering

Additive manufacturing of SiC-Sialon refractory with excellent properties by direct ink writing

Additive manufacturing of complexly shaped SiC with high density via extrusion-based technique – Effects of slurry thixotropic behavior and 3D printing parameters

Influence of Silicon Carbide on Direct Powder Bed Selective Laser Process (Sintering/Melting) of Alumina