Abstract:In this study, one of the commonly used MXene (Ti3C2Tx) and β nucleated isotactic polypropylene (β-iPP)/MXene composites of different compositions were fabricated. The effects of MXene on non-isothermal crystallization and polymorphic behavior of β-iPP/MXene composites were comparatively studied. The non-isothermal crystallization kinetics indicates that for all samples, the lower cooling rates promote composites to crystallize at higher temperatures. When MXene and β-Nucleating agent (β-NA) are added separately, the crystallization temperature of composites shifts towards higher temperatures at all cooling rates. When MXene and β-NA are added simultaneously, the composite shows different cooling rate dependence, and the effects of improving crystallization temperatures is more obvious under rapid cooling. The activation energy of four samples iPP, iPP/MXene, iPP/β-NA, and iPP/MXene/β-NA were −167.5, −185.5, −233.8, and −218.1 kJ/mol respectively, which agree with the variation tendency of crystallization temperatures. The polymorphic behavior analysis obtained from Differential Scanning calorimetry (DSC) is affected by two factors: the ability to form β-crystals and the thermal stability of β-crystals. Because β-crystals tend to recrystallize to α-crystals below a critical temperature, to eliminate the effect of β-α recrystallization, the melting curves at end temperatures Tend = 50 °C and Tend = 100 °C are comparatively studied. The results show that more thermally unstable β-crystals would participate in β-α recrystallization with higher cooling rates. Moreover, thermal stability of β-crystals is improved by adding MXene. To further verify these findings, samples of three different thermal conditions were synthesized and analyzed by DSC, X-Ray Diffraction (XRD), and Polarized Light Optical Microscopy (PLOM), and the results were consistent with the above findings. New understandings of synthesizing β-iPP/MXene composites with adjustable morphologies and polymorphic behavior were proposed.

Polypropylene Composites with Ultrahigh Low-Temperature Toughness by Tuning the Phase Morphology

Research on Toughening Modification of Copolymerized Polypropylene Using Polyolefin Elastomers

Toughening Mechanism of PP/EPR/SiO2 Composites with Superior Low-Temperature Toughness

Enhanced Multiphase Interfacial Interaction of Impact Polypropylene Copolymer by In-Situ Introducing Polyethylene

Exploring the Effects of MXene on Nonisothermal Crystallization and Melting Behavior of Β-Nucleated Isotactic Polypropylene

A facile fabrication of polypropylene composites with excellent low-temperature toughness through tuning interfacial area between matrix and rubber dispersion by silica nanoparticles located at the interface

A New Approach to Fabricate Polypropylene Alloy with Excellent Low-Temperature Toughness and Balanced Toughness-Rigidity Through Unmatched Thermal Expansion Coefficients Between Components

Ultra-high impact PPR composites at low-temperature through enhanced preferential loading of nanoparticles at polymeric interface induced by properly vulcanized rubber dispersed phase

Synergistic Toughening Effect of Olefin Block Copolymer and Highly Effective Β-Nucleating Agent on the Low-Temperature Toughness of Polypropylene Random Copolymer

Effect of Morphology Development on the Low‐temperature Tensile Properties of PP / POE Blends

Synergistic Improvement of Toughness of Isotactic Polypropylene: the Introduction of High Density Polyethylene and Annealing Treatment

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Ppr/Epdm/Poe-G-Ma/Ommt Nanocomposites with Superior Low-Temperature Toughness Based on Embedded Ommt Within Compound Rubber Dispersion Phase

Toughness and crystallization enhancement in wood fiber-reinforced polypropylene composite through controlling matrix nucleation

Toughening and strengthening of low-temperature resistant epoxy resins by introducing high-performance thermoplastic resin with phthalazinone structure

Realizing Simultaneous High‐temperature Strength and Low‐temperature Elongation in Polyolefin Elastomer Toughened Polypropylene Via Controlling the Dispersed Phase Size

Adjustable brittle-ductile transition behavior and rheological behavior of polypropylene random copolymer nanocomposites through well interfacial-loaded nanoparticles

Mechanism of low‐temperature brittle‐ductile transition of polypropylene/low‐density polyethylene blend foam under compressive stress caused by cells stretching

Phase Morphology and Impact Toughness of Impact Polypropylene Copolymer

The effect of elastomeric nano-particles on the mechanical properties and crystallization behavior of polypropylene

Mechanical properties and thermal stability of high-temperature (cooking temperature)-resistant PP/HDPE/POE composites