Abstract:Under the background of achieving carbon dioxide peaking and carbon neutrality, the rapid development of renewable energy power generation poses new challenges to the flexible adjustment capabilities of traditional power plants. To explore the furnace combustion stability and optimal operation modes during deep peak shaving, a simulation of the combustion process under low-load conditions for a 600 MW wall-fired boiler is performed utilizing computational fluid dynamics (CFD) analysis. The impact of burner combination modes on the combustion process within the furnace is explored at 25% and 35% boiler maximum continuous ratings (BMCRs). This study investigates two configurations of burner combinations. One mode operates burners in layers A, B, and C, which include the lower layers of burners on the front and rear walls of the boiler, as well as the middle-layer burners on the rear wall, referred to as OM1. The other mode operates burners in layers A and C, which include the lower layers of burners on the front and rear walls of the boiler, referred to as OM2. The results indicate that OM2 exhibits superior capabilities in orchestrating the distribution of the airflow velocity field and temperature field under the premise of ensuring no more than a 1% decrease in the pulverized coal burnout rate. When OM1 is employed, the airflow ejected from the middle-level burners hinders the upward movement of pulverized coal sprayed from the lower-level burners, causing a larger proportion of pulverized coal to enter the ash hopper for combustion. Consequently, the ash hopper attains a peak mole fraction of CO2 at 0.163. OM2 delays the blending of pulverized coal with air by enhancing the injection quantity of pulverized coal per burner. As a result, the generation of CO in the ash hopper reaches a notable mole fraction of up to 0.108. The decreased furnace temperature promotes the formation of fuel-based NOx during low-load operation. Taking the 25% BMCR as an example, the NOx emissions measured at the furnace outlet are 743 and 1083 ppm for OM1 and OM2, respectively. This study focuses on the impact of combustion combinations on the combustion stability when the boiler is operating at low loads. The findings could enrich previous research on combustion stability and contribute to the optimization of combustion schemes for power plant boilers operating at low loads.

Combined Operation Mode of Sub-Critical W-flame Boiler and Coal Mill Optimized Numerical Simulation

Study on coal combustion characteristics in a 350MW supercritical tangentially boiler

Optimal simulation on the combination mode of mills for an ultra-supercritical utility boiler

Experimental Study on Micronized Coal Reburning for a 200MW Coal-fired Boiler

Impact of Coal Types and Pulverizing Methods on the Thermal Performance of Blending Coal-Fired Boilers and Their Operational Optimization

Numerical Simulations Of Combustion Optimizaiton For A 600 Mw Tengentially Coal-Fired Super-Critical Boiler

B215 NUMERICAL SIMULATIONS OF COMBUSTION OPTIMIZAITON FOR A 600 MW TENGENTIALLY COAL-FIRED SUPER-CRITICAL BOILER(Combustion-8)

The integrated analysis of economy and safety on SOFA running mode of a 600MWe boiler

Characteristics of Combustion and NOx Emission in a 600 MWe Wall-Fired Boiler Under Varying Coal Mill and Burner Damper Configurations

Numerical Simulation Study on the Stable Combustion of a 660 MW Supercritical Unit Boiler at Ultra-Low Load

NOx Prediction Model for Multi-coal Admixing Combustion in Boiler

Numerical Investigation of Different Burner Arrangement on A Coal-Fired Boiler

Tertiary air operation optimization aiming at low NOx combustion in boiler

CFD modeling of hydrodynamics, combustion and NOx emission in a tangentially fired pulverized-coal boiler at low load operating conditions

Numerical Simulation on Burning Blended Coal Slime Under the Condition of Low Load in W-flame Boiler

Numerical simulation investigations into the influence of the mass ratio of pulverized-coal in fuel-rich flow to that in fuel-lean flow on the combustion and NOx generation characteristics of a 600-MW down-fired boiler

Numerical Study on Combustion Characteristics of a 600 MW Boiler Under Low-Load Conditions

Field Test and Numerical Simulation for Co-combustion of Sludge in a 100,MW Coal Fired Boiler

Numerical Simulation of Combustion in 35 t/h Industrial Pulverized Coal Furnace with Burners Arranged on Front Wall

Numerical simulation of the NO x emissions in a 1000 MW tangentially fired pulverized coal boiler: Influence of the multi-group arrangement of the separated over fire air

Co-combustion of sludge in a 100 MW unit coal-fired boiler:numerical simulation