Abstract:Heat generation, accumulation, and runaway severely affect the practical applications of lithium-ion batteries (LIBs) using Ni-rich Ni/Co/Mn ternary cathode materials. In principle, the aforementioned thermal characteristics of a LIB are mainly determined by the heat generation power of the cathode and anode materials during charging/discharging. In this work, the heat generation power of the LiNi0.8Co0.1Mn0.1O2 (NCM811) cathode material coated with and without reduced graphene oxide (rGO) is studied systematically. By coupling an electrochemical workstation with a multichannel microcalorimeter, the heat generation power of NCM811 under different charging/discharging conditions was measured on coin cells. Meanwhile, a theoretical model was also proposed to analyze the intrinsic factors of the NCM811 that possibly affect its heat generation power during electrochemical charging/discharging. The results show that the particle size, lithium-ion diffusion coefficient, specific heat capacity, thermal conductivity, and electric conductivity can all affect the heat generation power. Different from that, the particle size and the lithium-ion diffusion coefficient of NCM811 are the dominating factors. It is demonstrated further that by coating rGO onto NCM811, the lithium-ion diffusion coefficient of NCM811 is improved, and the heat generation power is reduced accordingly.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.2c00026.Schematic diagram of an in situ thermal/electrochemical testing system; the theoretical model of an NCM811 coin half-cell; the D50 values of four NCM811/rGO samples; the GITT potential curves versus testing time; the diffusion coefficients of Li+; the curves of heat flow at different voltages versus charging times; the DSC curves, the rate capability, and cycling stability data; the SEM image of NCM811/rGO-0.25 after cycling 100 times; the electrochemical/thermal model equations and boundary condition; and the parameters used for the simulation (PDF)This article has not yet been cited by other publications.

Effect of cation mixing of Li<SUP>+</SUP>/Ni<SUP>2+</SUP> on heat generation of NCM811 cathode during long-term cycling at elevated temperature

Effect of Cation Mixing of Li+/Ni2+ on Heat Generation of NCM811 Cathode During Long-Term Cycling at Elevated Temperature

Enhancing high-voltage performances of nickel-based cathode material via aluminum and progressive concentration gradient modification

Heat Generation Power of the LiNi0.8Co0.1Mn0.1O2 Cathode at Higher Charging Cutoff Voltages

Electrochemical performance and thermal stability analysis of LiNixCoyMnzO2 cathode based on a composite safety electrolyte

Impact of Evolution of Cathode Electrolyte Interface of Li(Ni0.8Co0.1Mn0.1)O2 on Electrochemical Performance During High Voltage Cycling Process

In Situ Mitigating Cation Mixing of Ni-Rich Cathode at High Voltage Via Li2mno3 Injection

Regulating the Heat Generation Power of a LiNi0.8Co0.1Mn0.1O2 Cathode by Coating with Reduced Graphene Oxide

Enhanced cyclic stability and discharge capacity of NCM811 cathode by coating ferroelectric-type LiNbO 3 ionically conductive layer

Investigation on the Thermal Behavior of Ni-rich NMC Lithium Ion Battery for Energy Storage

Towards the high-energy-density battery with broader temperature adaptability: Self-discharge mitigation of quaternary nickel-rich cathode

Regulating the Heat Generation Power of a LiNi 0.8 Co 0.1 Mn 0.1 O 2 Cathode by Coating with Reduced Graphene Oxide

Pre-Deoxidation of Layered Ni-Rich Cathodes to Construct a Stable Interface with Electrolyte for Long Cycling Life

Elucidating the Mechanical-Electrochemical Interactions in Single Crystalline LiNi 0 . 7 Co 0 . 1 Mn 0 . 2 O 2 Cathode Material During Solid-State Calcination

Elucidating the Mechanical-Electrochemical Interactions in Single Crystalline LiNi0.7Co0.1Mn0.2O2 Cathode Material During Solid-State Calcination

Thermal Expansion Neutralization Enhancing the Cycling Stability of Ni-Rich LiNi 0.6 Co 0.2 Mn 0.2 O 2 Cathode Material

Electrochemo‐Mechanical Effects on Structural Integrity of Ni‐Rich Cathodes with Different Microstructures in All Solid‐State Batteries

Engineering A Boron-Rich Interphase with Nonflammable Electrolyte Toward Stable Li||NCM811 Cells under Elevated Temperature

Dual-modified surface encapsulation strategy for elevating rate performance and cycling stability of Ni-rich NCM811 cathode

Optimizing NCM811 nickel-rich cathode stability via suppressing asymmetric Li/Ni mixing by a “non-intrusive” strategy

Surface-reinforced NCM811 with enhanced electrochemical performance for Li-ion batteries