Abstract:Aiming for increased nickel and lower cobalt content in layered transition metal oxide cathodes (NCM) is a feasible strategy for achieving increased energy density and cost competitiveness in commercial lithium‐ion batteries. However, the practical long‐term cycling of NCM cathodes suffers from severe capacity degradation due to irreversible interface phase transformation and unavoidable crack formation. Herein, an in situ modification strategy is used to form a uniform and conformal Li1.8Sc0.8Ti1.2(PO4)3 (LSTP) protective layer by interconnecting the single‐crystal‐layered LiNi0.6Co0.1Mn0.3O2 (SC‐NCM) particles. LSTP surface modification helps to construct a robust cathode‐electrolyte interphase thin film between the cathode and the electrolyte, which can prevent SC‐NCM corrosion by electrolyte, and the stability of the mechanics can improve the intergranular cracks caused by long cycles under harsh conditions. Moreover, the LSTP conductive modification layer facilitates the lithium‐ion transport among cathode particles, effectively enhancing the rate capability. Impressively, the LSTP modified SC‐NCM exhibits a high reversible capacity of 144.3 mAh g−1 at the high discharge rate of 5 C and maintains a capacity retention of 90.27% even at the ultrahigh charge voltage of 4.6 V operation after 500 cycles. Moreover, in a pouch‐type full battery, the graphite/LSTP modified SC‐NCM maintains a capacity retention of 89.6% after 1700 cycles. An innovative surface modification is developed to improve the long‐term cyclability and rate capability of a single‐crystalline Ni‐rich cathode. The surface modification strategy improves the mechanical stability and lithium‐ion transport, which creates a strong CEI interface to prevent electrolyte corrosion and improve the intergranular cracks caused by long cycles under harsh conditions.

Dual-modified surface encapsulation strategy for elevating rate performance and cycling stability of Ni-rich NCM811 cathode

Surface Coating of NCM-811 Cathode Materials with G-C3n4 for Enhanced Electrochemical Performance.

Dual Modification Strategy for Enhanced Cycling and Rate Performance of Ni-Rich Cathode Materials in Lithium-Ion Batteries

Stabilization of NCM811 cathode for Li-ion batteries by N-doped carbon coating

Elevating cycle stability of Ni-rich NCM811 cathode via single-crystallization integrating dual-modification strategy for lithium-ion batteries

Synergistic Effect of B-Nb Co-modified to Achieve Crystal Structure and Interface Tuning for Ni-rich Cathode

Protective and ion conductive: High-Rate Ni-Rich cathode with enhanced cyclic stability via One-Step bifunctional dual-layer coating

Realizing Dual Functions through Y2O3 Modification to Enhance the Electrochemical Performance of LiNi0.8Co0.1Mn0.1O2 Material

Protective and ion conductive: Ni-Rich cathode with enhanced electrochemical performance via dual-modification

Modifying surface chemistry and stress concentration to enable highly stable ultrahigh-Ni cathodes

Enabling the Strengthened Structural and Interfacial Stability of High‐Nickel LiNi0.9Co0.05Mn0.05O2 Cathode by a Coating‐Doping‐Microstructure Regulation Three‐In‐One Strategy

Stabilizing high-Ni cathodes with gradient surface Ti-enrichment

Polyvinylpyrrolidone-Induced Uniform Surface-Conductive Polymer Coating Endows Ni-Rich LiNi0.8Co0.1Mn0.1O2 with Enhanced Cyclability for Lithium-Ion Batteries.

Alleviating Structure Collapse of Polycrystalline LiNi X Co Y Mn1-x-y O2 Via Surface Co Enrichment

Synergistic effects of conformal surface precise nanofilm coating and doping on single-crystal LiNi0.5Co0.2Mn0.3O2 at high voltage

Enhanced rate performance and mitigated capacity decay of single-crystal LiNi0.8Co0.1Mn0.1O2 by the synergism of Mg doping and V2O5 coating

Improving the Performance of LiNi0.925Co0.065Mn0.01O2 via Ti4+& Nb5+ Co-Modifications

Surface Modification Engineering Enabling 4.6 V Single‐Crystalline Ni‐Rich Cathode with Superior Long‐Term Cyclability

Double Conductor Coating to Improve the Structural Stability and Electrochemical Performance of LiNi 0.8 Co 0.1 Mn 0.1 O 2 Cathode Material

Improving the Structure and Cycling Stability of Ni-Rich Layered Cathodes by Dual Modification of Yttrium Doping and Surface Coating

Engineering a Robust Interface on Ni-Rich Cathodes via a Novel Dry Doping Process toward Advanced High-Voltage Performance