Abstract:The growing need for sustainable and low-carbon energy sources has led to significant research in alternative fuels. The majority of energy produced today comes from fossil fuels, which has led to enormous emissions of greenhouse gases. The direct combustion of fossil fuels produces syngas and hydrogen, which contribute to global warming. In contrast, the gasification process of biomass produces clean energy in the form of syngas and hydrogen. The biomass and plastic co-gasification has gained a lot of attention recently due to the challenges associated with gasifying biomass and plastic wastes separately. The broader objectives of this study are to alleviate these waste management problems and optimize the syngas LHV and H 2 content using co-gasification process. The synthesis gas is a crucial intermediary used to create chemicals and fuels for transportation. The hydrogen component of synthesis gas can also be utilized directly as fuel for hydrogen fuel cells, which produce electricity. This work employs Aspen simulator to analyze an optimum processing condition where the synthesis gas has the maximum feasible hydrogen content and calorific value which has not been investigated in the available literature so far. Aspen software is used in this study since it can be useful in figuring out reaction yield and performing parametric studies to optimize process conditions. It is found that the carbon dioxide emission sharply decreases as the proportion of plastic increases in co-gasification. The mole fractions of CO, H 2 and CO 2 that the current model predicts using experimental data on rice husk have average modeling errors of less than 8%, indicating a satisfactory fit with the experimental findings. Under 1 bar of pressure and a combined feed rate of 100 kg/h for both plastic and biomass, the simulation was run at temperatures between 550 °C and 1300 °C. When steam was added, the fraction of hydrogen increased by approximately a factor of two for a steam-to-biomass ratio (SBR) of 2. Following the addition of plastic to the feed, the amount of hydrogen in the produced gas rose for all temperatures. When 15% plastic is combined with the feed at 850 °C, carbon dioxide is reduced by roughly 60%. The results indicate significant increase in calorific value of the product as well as the hydrogen proportion—suggesting plastic addition as an excellent method to improve the LHV of biomass gasification.

Maximizing hydrogen-rich syngas production from rubber wood biomass in an updraft fluidized bed gasifier: An advanced 3D simulation study

Simulation of air-steam gasification of pine sawdust in an updraft gasification system for production of hydrogen-rich producer gas

Hydrogen production via integrated configuration of steam gasification process of biomass and water‐gas shift reaction: Process simulation and optimization

Multi-Scale Simulation of Biomass Gasification in Fluidized Beds

An Experimental And Response-Surface-Based Optimization Approach Towards Production Of Producer Gas In A Circulating Fluidized Bed Gasifier Using Blends Of Renewable Fibre-Based Biomass Mixtures

Optimizing Hydrogen-Rich Biofuel Production: Syngas Generation from Wood Chips and Corn Cobs

Numerical Analysis of Biomass Gasification in a Fluidized Bed Reactor Using a Computational Fluid Dynamics Model Integrated with Reduced-Order Reaction Kinetics

Numerical simulation analysis of biomass gasification and rich-H2 production process in a downdraft gasifier

Hydrogen production from co-gasification of Çan lignite and sorghum biomass in a fixed-bed gasifier: CFD modeling

Effects of operating conditions and reactor structure on biomass entrained-flow gasification

Hydrogen production via gasification of corn stover: modeling and simulation using Aspen Plus®

Syngas-Enriched hydrogen production via catalytic gasification of water hyacinth using renewable palm kernel shell hydrochar

Simulation of Two-Phase Flow and Syngas Generation in Biomass Gasifier Based on Two-Fluid Model

CFD investigation of the complex multiphase flow of biomass gasification in industrial-scale dual fluidized bed reactor

Syngas and hydrogen production from co-gasification of rice husk biomass and plastic waste mixture using Aspen Plus

Numerical investigation of different biomass feedstock on syngas production using steam gasification and thermodynamic analysis

Optimization of hydrogen and syngas production from PKS gasification by using coal bottom ash

Numerical Simulation of Biomass Gasification in a Bubble Fluidized Bed

Exploring the synergetic effects of rice husk, cashew shell, and cashew husk biomass blends on fluidized bed gasification for enhanced hydrogen production

Optimization of the Three-Stage Biomass Gasification Characteristics in High-Temperature Entrained-Flow Bed

High value-added syngas production by supercritical water gasification of biomass: Optimal reactor design