Abstract:Tip clearance flow between rotating blades and the stationary casing in high-pressure turbines is very complex and is one of the most important factors influencing turbine performance. The rotor with a winglet-cavity tip is often used as an effective method to improve the loss resulting from the tip clearance flow. In this study, an aerodynamic geometric optimisation of a winglet-cavity tip was carried out in a linear unshrouded high-pressure axial turbine cascade. For the purpose of shaping the efficient winglet geometry of the rotor tip, a novel parameterisation method has been introduced in the optimisation procedure based on the computational fluid dynamics simulation and analysis. The reliability of a commercial computational fluid dynamics code with different turbulence models was first validated by contrasting with the experimental results, and the numerical total pressure loss and flow angle using the Baseline k-omega Model (BSL κ-ω model) shows a better agreement with the test data. Geometric parameterisation of blade tips along the pressure side and suction side was adopted to optimise the tip clearance flow, and an optimal winglet-cavity tip was proven to achieve lower tip leakage mass flow rate and total pressure loss than the flat tip and cavity tip. Compared to the numerical results of flat tip and cavity tip, the optimised winglet-cavity design, with the winglet along the pressure side and suction side, had lower tip leakage mass flow rate and total pressure loss. It offered a 35.7% reduction in the change ratio [Formula: see text]. In addition, the optimised winglet along pressure side and suction side, respectively, by using the parameterisation method was studied for investigating the individual effect of the pressure-side winglet and suction-side winglet on the tip clearance flow. It was found that the suction-side extension of the optimal winglet resulted in a greater reduction of aerodynamic loss and leakage mass flow than the pressure-side extension of the optimal winglet. Moreover, with the analysis based on the tip flow pattern, the numerical results show that the pressure-side winglet reduced the contraction coefficient, and the suction-side winglet reduced the aerodynamic loss effectively by decreasing the driving pressure difference near the blade tips, the leakage flow velocity, and the interaction between the leakage flow and the main flow. Overall, a better aerodynamic performance can be obtained by adopting the pressure-side and suction-side winglet-cavity simultaneously.

Influence of spacing of a delta-winglet vortex generator pair on the flow behavior and heat transfer at the internal tip of gas turbine blades

On the Topology of Vortex Structures and Heat Transfer of a Gas Turbine Blade Internal Tip with Different Arrangement of Delta-Winglet Vortex Generators

Heat Transfer Characteristics of Blade Internal Tip Surface by Arrays of Delta-Winglet Vortex Generator Pairs

THE AUGMENTATION OF INTERNAL TIP HEAT TRANSFER IN GAS TURBINE BLADES USING A PAIR OF DELTA-WINGLET VORTEX GENERATORS

Transpiration Cooling of High Pressure Turbine Vane with Optimized Porosity Distribution

Vortical Structures and Heat Transfer Augmentation of a Cooling Channel in a Gas Turbine Blade with Various Arrangements of Tip Bleed Holes

Experimental investigation of secondary flow losses in a variable geometry linear turbine cascade with winglet tip

On the Heat Transfer and Flow Structures’ Characteristics of the Turbine Blade Tip Underside With Dirt Purge Holes at Different Locations by Using Topological Analysis

Numerical Investigations on the Effect of Blade Tip Winglet on Leakage Flow Loss Reduction for a Zero Inlet Swirl Turbine Rotor

Experimental and numerical investigations of tip clearance flow and loss in a variable geometry turbine cascade

Experimental evaluation of longitudinal and transverse vortex generators on the endwall of a serpentine passage

Improved clearance designs to minimize aerodynamic losses in a variable geometry turbine vane cascade

Predictions of Enhanced Heat Transfer of an Internal Blade Tip-Wall with Hemispherical Dimples or Protrusions

Heat Transfer of Winglet Tips in a Transonic Turbine Cascade

Parametric study of major factors affecting heat transfer enhancement in a circular tube with vortex generator pairs

Flow and Heat Transfer Characteristics in Models of Turbine Blade Tip-Walls with Three Kinds of Turning Vanes

Impact of Delta Winglet Vortex Generators on the Performance of a Novel Fin-Tube Surfaces with Two Rows of Tubes in Different Diameters

Analysis of enhanced turbulent heat transfer in a sharp turn channel having novel designed endwall with longitudinal vortex generator

Influence of the Upstream Slot Geometry on the Endwall Cooling and Phantom Cooling of Vane Suction Side Surface

Aerodynamic Effects of an Incoming Vortex on Turbines with Different Tip Geometries

Aerodynamic Optimisation of a Winglet-Cavity Tip in a High-Pressure Axial Turbine Cascade